User Manual - Iberna LSI 47 Manual Del Usuario

USER MANUAL

GB
UNIVERSAL REMOTE CONTROL
Thank you for purchasing this universal remote control. Before using the
remote you will need to insert 2 type "AAA" batteries (not included) in the
battery compartment ensuring that you follow the polarity shown on the inside.
You can now use your remote control to operate up to 9 different devices
(depending on the model) including a TV, video recorder, DVD player, satellite or
cable receiver, CD player, tuner (radio), tape recorder and amplifier. If your
remote control is equipped with an AUX key (not standard on all models) then
you can also use it to control a second TV set, video recorded, satellite receiver
and/or cable box, CD player, tuner, tape recorder or amplifier!
Easy programming for the control of your TV SET
1. Insert 2 new 1.5V alkaline batteries of type "AAA/LR03". Observe battery
polarity as indicated in the battery compartment.
2. Switch on your TV SET.
3. In the enclosed code list, find your TV brand or manufacturer (e.g. Sony).
4. Beside the manufacturer's name, you will find one or more 3-digit codes.
These codes must be entered into the remote to enable it to work with your
particular TV set.
5. Press the key on the remote control for approximately 4 seconds until
TV
the LED flashes twice.
6. After seeing the 2 flashes and within 5 seconds, enter the 3-digit numerical
code from the list.
7. After entering the code the LED will flash twice indicating that the code has
been accepted.
8. Point the remote control towards your TV and press the
does not respond by going into Stand-By mode then repeat steps 3 to 8
and enter the next code in the list.
9. If your TV goes into Stand-By mode when the
remote control has found a compatible code. Next test all of the other
function buttons. If certain functions are not working correctly then restart
the process moving onto the next code number as this may well improve
the situation.
10. If the codes in the list fail to operate your TV then next move onto the
automatic code scan function (see below).
Easy programming for the control of your VIDEO
RECORDER
To programme the remote control to operate your VIDEO RECORDER, proceed
as described above for the television set. Complete steps 1 to 10 using the
key on your remote control. Please ensure that you refer to the codes
VCR
listed under the VIDEO RECORDER section and not the TV section.
Easy programming for the control of your SATELLITE
RECEIVER
To programme the remote control to operate your SATELLITE RECEIVER or
CABLE BOX, proceed as described for the television set. Complete steps 1 to
10 using the key on your remote control. Please ensure that you refer to
SAT
the codes listed under the SATELLITE section and not the TV section.
Easy programming for the control of your DVD PLAYER
To programme the remote control to operate your DVD PLAYER, proceed as
described for the television set. Complete steps 1 to 10 using the
your remote control. Please ensure that you refer to the codes listed under the
DVD section and not the TV section.
Easy programming for the control of your CD PLAYER
To programme the remote control to operate your CD PLAYER, proceed as
described for the television set. Complete steps 1 to 10 except you must first
press and release the key followed by holding down the
SHIFT
ensure that you refer to the codes listed under the CD section and not the TV
section.
key. If your TV
key pressed then your
key on
DVD
key. Please
CD
2
USER MANUAL
GB
Easy programming for the control of your TUNER
(RADIO)
To programme the remote control to operate your TUNER, proceed as
described for the CD PLAYER but using the
Please ensure that you refer to the codes listed under the TUNER section and
not the CD PLAYER section.
Easy programming for the control of your TAPE
RECORDER (TAPE DECK)
To programme the remote control to operate your TAPE RECORDER, proceed
as described for the CD PLAYER but using the
Please ensure that you refer to the codes listed under the TAPE section and not
the CD PLAYER section.
Easy programming for the control of your AMPLIFIER
To programme the remote control to operate your AMPLIFIER, proceed as
described for the CD PLAYER. Complete steps 1 to 10, using the
your remote control. Please ensure that you refer to the codes listed under the
AMPLIFIER section and not CD PLAYER section.
Code scan
If programming using the codes in the enclosed list failed to work then you
must next try the automatic code scan.
A. Ensure that the remote control is equipped with 2 new batteries (see step
one of easy programming procedure).
B. Switch on your TV SET. When using the automatic scan function for the
VCR, DVD, CD or TAPE, switch on your device, insert a video tape, DVD,
CD or tape cassette and put the unit into 'Play mode' i.e, the VCR tape etc
is running.
C. Press the key of your remote control for approx. 4 seconds until the
TV
LED flashes twice.
D. After seeing the 2 flashes and within 5 seconds, enter the code
After entering the code the LED will flash twice indicating that the code has
been accepted
E. Press and hold the key until your TV switches off. Please note that this
process might take up to 15 minutes. During the automatic scanning you
can remove your finger or change hands provided it is replaced within 8
seconds. If left off of the key for more than 8 seconds then the remote will
revert back to its normal mode. If your TV switches into Stand-By mode
during the automatic process then immediately remove your finger from the
key and then press and release the
twice, this will then store the code that the remote has found
F. In some cases during the automatic scanning search the remote control
might find several codes that appear to operate your TV etc, however, if
some of the buttons fail to work properly then it's possible the remote has
found a partially compatible code. In such cases you will need to restart the
automatic scanning process (steps B. to F.) until a better code is found.
Please note that once the automatic process is restarted, the remote
continues from the last stored code and not at the beginning of code
database.
• To complete a code scan for the VCR, DVD, CD or TAPE, follow the
procedure above but use the
• To complete a code scan for the TUNER, follow the procedure above but
use the key
2
key instead of the CD key.
TUNER
key instead of the CD key.
TAPE
AMP
0
key until the LED flashes
TV
key and not the key
3
key on
.
0 1