Oxybul éveil & jeux FREEBUL Manual Del Usuario página 4

Keep the instructions for future.
NF-EN-71
Warning! Protective equipment should be worn.
Not to be used in
20 kg max.: Seat mode (balance bike, ride on)
50 kg max.: Scooter mode
Seat mode: Warning! Not to be used by children over 36 months due to the limited
strength of the seat bracket frame. The seat can only be used with this
product when the steering is completely locked by the parents using the locking
button located at the upper side of the steering assembly. Press down the locking
button in order to lock the steering of the wheels when the seat is to be mounted.
Remove the scooter and all the parts from the box. Set out all the parts
and read the assembly instructions prior to use. Keep the packaging until
assembly is complete.
General instructions
This toy must be assembled by a responsible adult. Prior to use, make sure
that the toy has been assembled properly. Remove all the parts which are not
necessary for play before giving the toy to your child. The toy should be used with
caution since skill is required to avoid falls or collisions causing injury to the user
or third parties.
To use with suitable protective equipment, including a helmet, shoes, elbow, wrist
and knee protectors. Teach the child how to use it safely and responsibly.
Directions:
- The scooter can be dangerous and can cause accidents when used on
public highways. Don't use on the on public roads. It is best used on a
surface, free of gravel and grease. Avoid bumps and drainage grates that may
cause an accident.
- The scooter does not include any headlights or lights. It is therefore not suited for
use at night or during periods when visibility is limited.
- Always use under adult supervision.
- Do not allow more than one child to ride the scooter at the same time.
6
Before and after use:
- Make sure that all locking mechanisms are securely locked:
- Check the height of the steering system, and make sure the nuts are tightened
and that the handlebars and the front wheel are perpendicular.
- The minimum height of T-bar has to be locked at the lowest position by switching
the bullet into the lowest slot. (see 'E' diagram).
- Check all of the connection elements: the brake, the steering column's quick
release system and the wheel axles must be adjusted correctly and not damaged.
- Also check the tyre wear.
INSTALLATION AND USE OF SEAT FOR USE walking-bike / Ride-on
(see page 2)
Product 4 in 1 comes with a connector tube which is used to
Assemble the tube according to the size of the child, who it must always have 2
feet resting on the ground when in sitting position on the seat (Figure 1).
Warning. Be careful to never leave a tube mounted on the deck of the scooter
without the seat. Insert the connector tube into the front hole of the seat,
following the direction of insertion for be able to set the screw.
Insert the screw for the connector tube to the seat, tighten with the allen key
(Figure 2).
Insert the connector tube with seat in the front hole of the deck scooter between the
two front wheels, following the direction of insertion.
Make sure the spring button is engaged and locked correctly as shown (Figure 3).
clean
Using the handlebars as parent handle: the handlebar of the scooter can be
used as parental cane. Insert the handle into the back hole of the seat, respecting
the way of insertion. Make sure the spring loaded button is engaged and locked
correctly as shown (Figure 4).
Steering: ride on the seat, feet resting on the the child pushes with his feet to
advance. He must proceed with caution at
Parent handle can be used to accompany children during the
SCOOTER ASSEMBLY (see page 2)
Insert the handle bars into the hole at the front of the main board between the two
front wheels while paying attention to the direction of insertion.
Ensure the spring button pops out and locks the piece properly, as shown.
(Diagram A)
Product is proposed with an adjustable handlebar which can be adapted to the child's
height (3 Positions).
The bullet shall be in the hole while adjusting the T-bar height.
Make sure that for the lowest position of T-bar, the bullet is locked into the lowest
slot (see 'E' diagram)
Steering: Product's steering responds intuitively to the movement of the body
(Diagram B).
the seat . - When the child leans to the right,product turns right!
- When the child leans to the left, product turns left!
For the youngest children, on surfaces and in straight lines, product has a steering
blocking system for better balance and to make learning easier .
- To lock, press the button above (Diagram C)
- To release, press the red button below (Diagram D)
During use:
- Standing on the scooter, one hand on each handle, push with one of your feet to
move forward. Proceed with caution at the start.
- Braking: a brake is located at the rear, when necessary press down on it to slow
down. Press down gradually in order to prevent skidding or loss of stability.
- Shoes are mandatory and we strongly advise you to wear trousers and long
sleeve shirts to avoid injury if you fall.
- Explain to the child clearly how to lock the scooter before any use.
use.
Care / Maintenance:
Regular maintenance is a safety commitment:
- Wheel bearings: avoid going through water, oil or sand as this can damage
wheel bearings.
- Wheels: the wheels wear down with time and can be damaged if overly used
on rough surfaces. The back wheel on which the brake is applied is particularly
affected after several hours of braking. In the interests of safety, they should be
checked regularly and changed if necessary.
- the original product must by no means be except for the
maintenance-related changes mentioned in these instructions.
- Nuts and axles: these should also be checked regularly. They can become loose
after a while in which case they should be tightened. They can become worn and
not tighten properly, in which case they should be replaced.
- Cleaning: Clean the scooter with a soft cloth and a little water.
7