Publicidad
Idiomas disponibles
Idiomas disponibles
OBJ_BUCH-0000000100-001.book Page 30 Monday, November 26, 2012 10:16 AM
en
30
Character
Unit of measurement,
international
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
2
min, m/s
For your safety.
Read all safety warnings and all
WARNING
instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have thor-
oughly read and completely understood this
Instruction Manual and the enclosed "General
Safety Instructions" (document number
3 41 30 054 06 1). The documents mentioned should be
kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial safety
regulations.
Intended use of the power tool:
hand-guided power tool for use in weather-protected
environments without water supply, using the cutting
wire and accessories recommended by FEIN:
– for cutting polyurethane beads for glazier work in
automobiles, lorries and busses
– for removing auto glass with minor gap clearance
between glass and frame
– for removing glass in hard-to-reach locations and par-
tially covered off areas (e. g. by the cockpit, steering
wheel, linings, covers)
Special safety instructions.
Hold the power tool by the insulated gripping surfaces
when performing operations where the cutting wire could
contact hidden wires. Contact with a "live" wire will also
make exposed metal parts of the power tool "live" and
shock the operator.
Grasp/hold the power tool in such a safe manner that
your body never comes in contact with the cutting wire.
Touching sharp cutting edges or edges can lead to injury.
Wear personal protective equipment. Depending on appli-
cation, use face shield, safety goggles or safety glasses.
Where appropriate, wear dust mask, hearing protectors,
gloves and workshop apron capable of stopping small
abrasive or workpiece fragments. The eye protection
must be capable of stopping flying debris generated by
various operations. The dust mask or respirator must be
capable of filtrating particles generated by your opera-
tion. Prolonged exposure to high intensity noise may
cause hearing loss.
Do not direct the power tool against yourself, other per-
sons or animals. Danger of injury from the sharp or hot
cutting wire.
Do not rivet or screw any name-plates or signs onto the
power tool. If the insulation is damaged, protection
against an electric shock will be ineffective. Adhesive
labels are recommended.
Unit of measurement,
Explanation
national
m, s, kg, A, mm, V,
Basic and derived units of measurement from the
W, Hz, N, °C, dB,
international system of units SI.
2
min, m/s
Clean the ventilation openings on the power tool at regu-
lar intervals using non-metal tools. The blower of the
motor draws dust into the housing. An excessive accu-
mulation of metallic dust can cause an electrical hazard.
Use and handling of the battery (battery pack).
To avoid hazardous situations such as burns, fire, explo-
sion, skin injuries, and other injuries when handling the
battery, observe the following instructions:
Batteries must not be disassembled, opened or reduced
in size. Do not subject batteries to mechanical impact or
shock. Hazardous vapours and fluid can escape in case of
damage and improper use of the battery. The vapours can
irritate the respiratory system. Liquid ejected from the
battery may cause skin irritations or burns.
When battery fluid from a damaged battery has come into
contact with objects close by, check the respective com-
ponents, clean them or replace them as required.
Keep the battery away from heat and fire. Do not store the
battery in direct sunlight.
Do not remove the battery from its original packaging
until it is going to be used.
Before any work on the machine itself, remove the bat-
tery from the power tool. If the power tool accidentally
starts, there is danger of injury.
Remove the battery only when the power tool is switched
off.
Keep the battery away from children.
Keep the battery clean and protect it against moisture
and water. Clean contaminated battery terminals and
power tool connections with a dry, clean cloth.
Use only intact original FEIN batteries that are intended
for your power tool. When working with and charging
incorrect, damaged, repaired or reconditioned batteries,
imitations or other brands, there is danger of fire and/or
explosion.
Follow the safety warnings in the operating instructions
of the battery charger.
Operating Instructions.
Do not use accessories not specifically intended and
recommended for this power tool by FEIN. The use of non-
original FEIN accessories can lead to overheating of the
power tool and destroy it.
Handling the glass-removal machine and the
remote control.
Always fasten the glass-removal machine on the inside of
the windshield/glass in the centre (see page 5–7). In this,
align the glass-removal machine diagonally, so that the
drive unit faces downward. Position the deflectors as
close as possible to the window corners.
Publicidad
