Descargar Imprimir esta página

Publicidad

Enlaces rápidos

Instruction Manual
NS-HMC1
PACKAGE CONTENTS
y 1 – Multi-Angle Helmet Mount
y 1 – 5/16" - 18 x 1/4" Light Mounting Allen Set Screw (installed in mount)
y 2 – 5/16" - 18 x 1/4" Brim Mounting Allen Set Screws (installed in mount) – for Fire Helmets
y 2 – 5/16" - 18 x 3/8" Brim Mounting Allen Set Screws (loose) – for Hard Hats
y 1 – 5/32" Allen Wrench
APPLICATION
The NS-HMC1 Multi-Angle Helmet Mount is a mounting bracket for attaching a
fl ashlight that has a 1" handle diameter to any Fire Helmet or Hard Hat.
The mount can be attached to either side of most Fire Helmets or Hard Hats and
provides 140 degrees of adjustability. This allows the user to position the light for clearance
around face shields, goggles or other potential obstructions.
INSTALLING THE LIGHT INTO THE MULTI-ANGLE MOUNT
Begin by deciding which side of the helmet the NS-HMC1 and fl ashlight are to be
attached. This will determine the proper orientation of the light in the mount. Additionally
check that the fi nal location on the helmet does not interfere with the normal operation of
face shields, goggles, etc.
Image 1
y Remove the 5/16" - 18 x 1/4" Light Mounting Allen Set Screw from the Multi-Angle
Helmet Mount and slip the fl ashlight into the mount. (Image 1)
y NOTE: The Multi-Angle Helmet Mount may be positioned anywhere along the length
of the fl ashlight handle. (Image 2)
y Once the light is in the proper position, re-install the Light Mounting Allen Set Screw
and tighten, securing the fl ashlight in place. (Image 3)
CAUTION: Be careful when tightening the Allen Set Screw. Do not over-tighten.
Doing so may damage the handle of the light. The Allen Set Screw should only be
tightened enough to prevent the light from coming loose. Over time this screw may
come loose. Periodically check and re-tighten as needed.
SUGGESTION: Application of a thread locking solution (such as Loctite®
Threadlocker Blue) may be applied to secure the Allen Set Screw. Do not use the "red"
version of this product as it is designed for a more permanent installation and would make
it diffi cult to remove the Allen Set Screw in the future.
INSTALLING THE NS-HMC1 & LIGHT ON TO THE HELMET
Once the fl ashlight has been installed into the Multi-Angle Helmet Mount, the entire unit is
ready to be attached to the Fire Helmet or Hard Hat. The Multi-Angle Mount comes with two
5/16" - 18 x 1/4" Brim Mounting Allen Set Screws pre-installed. These two Allen Set Screws
are designed to be used with the thicker brim found on most Fire Helmets. (Image 4) It may be
necessary to switch these two Allen Set Screws with the 5/16" - 18 x 3/8" set if the thickness
of the brim of the helmet or Hard Hat makes it impossible to use the shorter set. (Image 5)
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.com
Image 2
Image 3
y Position the Multi-Angle Mount over the edge of the brim and tighten the appropriate
set of Allen Set Screws using the included 5/32" Allen Wrench. (Image 6)
Image 4
CAUTION: Be careful when tightening the Allen Set Screws. Do not over-tighten.
Doing so may damage or crush the brim of the Fire Helmet or Hard Hat. These
two Allen Set Screws should only be tightened enough to prevent the mount
from coming loose from the helmet. Over time these screws may come loose.
Periodically check and re-tighten as needed.
SUGGESTION: Application of a thread locking solution (such as Loctite®
Threadlocker Blue) may be applied to secure these Allen Set Screws. Do not use the
"red" version of this product as it is designed for a more permanent installation and would
make it diffi cult to remove these Allen Set Screws in the future.
SETTING THE ANGLE OF THE MULTI-ANGLE MOUNT
Image 7
Once mounted, the user can adjust the angle of the mount through 140 degrees to
position the light for optimum clearance and illumination. (Image 7)
y To adjust the angle, simply loosen the Angle Lock Socket Head Cap Screw using the
included 5/32" Allen Wrench. (Image 8)
y Select the angle and then tighten the Angle Lock Socket Head Cap Screw securely.
(Image 9)
y Test to make sure that the angle will not change and continue tightening as needed.
WARRANTY
1 YEAR WARRANTY
Bayco Products, Inc. warrants this product to be free from defects in workmanship
and materials to the original purchaser for 1 year from the date of purchase, and includes
the LEDs, housing, lenses, electronics, switches, rechargeable batteries and chargers.
Bulbs (other than LEDs) are covered for 90 days from the date of purchase.
We will repair or replace this product should we determine it to be defective. This is the
only warranty, expressed or implied, including any warranty of merchantability or fi tness for
a particular purpose.
For a complete copy of the warranty, go to www.baycoproducts.com/nightstick-product-
support/warranties. Retain your receipt for proof of purchase.
CONTENU DE LA BOÎTE
y 1 – NS-HMC1 Dispositif pour casque à angle multiples
y 1 – Ensemble de vis à têtes creuses pour dispositif de lampe de poche (déjà monté)
de 5/16 '' – 18 x ¼ ''
y 1 – Ensemble de vis à têtes creuses pour dispositif de rebord (déjà monté) de 5/16
'' – 18 x ¼ '' – pour casques d'incendie
y 2 – Ensemble de vis à têtes creuses pour dispositif de rebord (lâches) de 5/16" - 18
x 3/8" – pour casques durs
y 1 – Clé Allen de 5/32''
COMPOSANTES
Le dispositif pour casque à angles multiples est un support de montage pour fi xer une
lampe de poche de 1 pouce de diamètre à n'importe quel casque d'incendie ou casque dur.
Le dispositif pour casque à angles multiples peut être fi xé sur n'importe quel côté du
casque d'incendie ou casque dur et procure une capacité d'ajustement de 140 degrés.
Cet ajustement permet à l'utilisateur de régler de façon optimale la lumière afi n de
procurer une clarté autour du masque de protection, lunettes de protection et autres
obstacles pouvant obstruer la vue.
INS-NS-HMC1-21
Image 5
Image 8
Mode D'Emploi
NS-HMC1
Image 6
Image 9

Publicidad

loading

Resumen de contenidos para NightStick NS-HMC1

  • Página 1 Allen Set Screws with the 5/16” - 18 x 3/8” set if the thickness of the brim of the helmet or Hard Hat makes it impossible to use the shorter set. (Image 5) Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.com INS-NS-HMC1-21...
  • Página 2 Remarque : Le dispositif pour casque à angles multiples peut être placé à n’importe Comience por decidir de qué lado del casco del NS-HMC1 y de la linterna se van a quel endroit sur le manche de la lampe de poche. (Image 2) conectar.