Flymo C-Li 20VHT Manual De Usuario página 7

• Do not keep a battery pack on continuous charge when
not in operation.
• Save the manual to refer to it in the future.
• Only use the battery pack for its necessary operation.
• Remove the battery pack from the product when not in
operation.
• Keep the battery pack away from paper clips, keys,
nails, screws, or other small metal objects while in
operation. This can make a connection between
terminals. Shorting the battery pack terminals together
can cause burns or a fi re.
CHARGER USE AND CARE
• Before using the charger, read all instructions and
cautionary markings for the charger, battery pack,
and the product using the battery pack.
• Do not allow any liquid to get inside charger.
•
To reduce the risk of injury, charge only
designated batteries. The charger and battery pack
are specifi cally designed to work together. Other types
of batteries may burst, causing personal injury and
damage.
•
Under certain conditions, with the charger
plugged in to the power supply, the charger can
be shorted by foreign material. Foreign materials of
a conductive nature such as, but not limited to, steel
wool, aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities.
•
Always unplug the charger from the power supply
when there is no battery pack in the cavity.
•
The charger is not intended for any uses other
than charging the designated rechargeable
batteries. Any other uses may result in risk of fi re,
electric shock or electrocution.
•
Do not expose the charger to rain or snow.
•
Pull by the plug rather than the cord when
disconnecting the charger. This will reduce the risk
of damage to the electric plug and cord.
•
Make sure that the cord is located so that it will
not be stepped on, tripped over, or otherwise
subjected to damage or stress.
•
Do not operate the charger with a damaged cord or
plug. Have them replaced immediately.
•
Do not operate the charger if it has received
a WARNING! Do not install the battery pack until the
power tool is completely assembled.
ASSEMBLING THE ATTACHMENT
Insert the attachment into the powerhead until it clicks into
position. Make sure the attachment release button passes
completely through the hole.
BEFORE STARTING
• Make sure you have the proper personal protective
equipment.
• Inspect the cleanliness of the power tool. Make sure the
handles are dry, clean, and free of oil and grease.
• Inspect for correct alignment of moving parts.
• Inspect for broken or damaged parts. Do not use the
power tool if any damage affects safety or operation.
Have damage repaired by an authorized service center.
• Lubricate the cutting blades.
• Install the battery pack
a sharp blow, has been dropped, or has been
damaged in any other way. Take it to an authorized
service center.
•
Do not disassemble the charger. Take it to an
authorized service center when service or repair is
required. Incorrect reassembly may result in a risk of
electric shock, electrocution or fi re.
•
Disconnect the charger from the outlet before
attempting any cleaning. This will reduce the risk
of electric shock. Removing the battery pack will not
reduce the risk.
•
Do not attempt to connect 2 chargers together.
•
The charger is designed to operate on standard
household electrical power (120 Volts). Do not
attempt to use it on any other voltage.
Electrical outlets
a WARNING: Do not touch the terminals of the plug
when installing or removing the plug from the
outlet.
Before plugging in the charger, make sure that the outlet
voltage supplied is within the voltage marked on the
charger's data plate.
Extension cords
Do not use an extension cord unless it is absolutely
necessary. Use of improper extension cord could result in
risk of fi re, electric shock, or electrocution.
a WARNING: Do not touch the terminals of the plug
when installing or removing the plug from the
extension cord.
When using an extension cord, be sure to use one heavy
enough to carry the current that your power tool will draw.
An undersized extension cord will cause a drop in line
voltage resulting in loss of power and overheating.
MAINTENANCE AND STORAGE
• Remove the battery before carrying out maintenance or
cleaning work.
• Use only the manufacturer's recommended replacement
parts and accessories.
• Inspect and maintain the product regularly. Have the
product repaired only by an authorized repairer.
• When not in use, store the product out of the reach of
children.
ASSEMBLY
NOTE: To remove the attachment, press down fi rmly
on the attachment release button while pulling the
attachment out of the powerhead.
OPERATION
INSTALLING THE BATTERY PACK
NOTE: The battery pack is not shipped fully charged.
It is recommended that the battery pack be fully
charged before initial use. With regular use, the
battery pack will take 4 hours or less to fully charge.
It is recommended that the battery pack be charged
every 3 months when the tool is not in use. The
battery pack's run time will improve after the third or
fourth charge.
1. Align the tongue of the battery pack with the cavity in
the powerhead.
2. Grasp the rear handle fi rmly.
7