Before Use; Carry Handle/S - Black+Decker BXCSH2001E Traducción De Instrucciones Originales

sories are used to replace existing parts/accessories.
♦ WARNING: There is a risk of fire if the appliance is not
cleaned according to these instructions.
♦ Misuse or failure to follow the instructions may be
dangerous and renders the manufacturer's guarantee
null and void.
DESCRIPTION
1 Air outlet
2 Carry handle
3 Display
4 On / Off switch
5 Front panel
6 Standing feet
7
On / Off button
Low power indicator
8
Button (-)
9
10 Brightness/Timer button
Temperature/Timer display
11
12
High power indicator
13 Button (+)
Fitting the base feet
♦ The appliance has base feet (6) on which the product
♦ can be supported.
♦ To fit the base feet, place the appliance face down.
♦ Place the base feet on the body of the appliance.
♦ Use the screws to attach feet to the body (Supplied
with
♦ the appliance)
♦ Stand the appliance up again and check that the base
♦ feet work properly.
INSTRUCTIONS FOR USE

Before use:

♦ Make sure that all the product's packaging has been
♦ removed.
♦ Certain parts of the appliance have been lightly greased,
♦ consequently, the appliance may give off a light smoke
♦ the first time it is used. After a short time, this smoke will
♦ disappear.
♦ To eliminate the smell given off by the appliance when
♦ used for the first time, it is recommended to have it on at
♦ full power for 2 hours in a well-ventilated room.
♦ Prepare the appliance according to the function you wish to
use.
Use:
- Unroll the cable completely before plugging it
in.
- Connect the appliance to the mains.
- Turn the appliance on, by using the on/off
button (4).
- Press the button 14 for one time, the appliance
will work with low heating (1250W). Press
again, it will change to high heating (2000W)
Power setting button
14
15 Screws
Timer function
Press the button 10 to set the timer (1-9 hours).
Pressing the button 9 to increases one hour. Pressing
the button 13 to decreases one hour.
SET THE TEMPERATURE:
•During working status, press +/- buttons. The display will
show 23ºC as default.
•Press +/- to set the desired temperature (10-35ºC)
•When the temperature reaches 10ºC, press – (9) again, the
anti-frost function will be activated, the screen will display AF.
Notice: When it is in anti-frost function, the target temp is 7 ºC.
BRIGHTNESS OF LED DISPLAY
The default brightness is 100%. Press the button 10 to
change the brightness from 100%, 50%, 25%, and 0%
display in a continuous cycle.
But even select 0% brightness, the standby button 7 and the
button 10 will always keep as 25% brightness.
Notice: If there are no operations in1 minute when it is in
100% brightness, the brightness would turn to 50%.
When it is 0% display situation, the screen would display as
25% brightness if there are any operations.
- ONCE YOU HAVE FINISHED USING THE APPLIANCE:
-
Turn the appliance off using the on/off button.
-
Unplug the appliance from the mains.
-
Clean the appliance.

Carry handle/s:

♦ This appliance has a handle on the side of the
body, which facilitates comfortable transport (2)
SAFETY THERMAL PROTECTOR:
The appliance has a safety device, which protects the
appliance from overheating.
When the appliance switches itself on and off repeatedly,
for reasons other than the thermostat control, check to
ensure that there are no obstacles that impede correct air
entry or expulsion.
If the appliance turns itself off and does not switch itself
on again, disconnect it from the mains supply, and wait for
approximately 15 minutes before reconnecting. If the
machine does not start again seek authorised technical
assistance.
5