Converting The Seat: Semi-Rigid Carry Cot Con- Figuration - Chicco FULLY Instrucciones De Uso

pram/semi-rigid carrycot configuration).
To remove the belts, unfasten the waist belt from the rela-
tive "D''-shaped rings and the shoulder straps from the fab-
ric slots located on the backrest. After removing the safety
belts, make sure that the belts are re-assembled properly
using the anchoring points.
WARNING: Once the safety belts are removed, keep them
out of the reach of children and store them for future use.
To re-assemble the safety harnesses, carefully follow the
steps below:
21. Pass the belt through the upper slot (Fig. 21), making
sure that the length adjuster is positioned as shown in
Fig. 21A.
22. Take the plastic slot end of the shoulder straps and intro-
duce it into the safety belt's fabric ring (Fig. 22).
23. Having performed this operation correctly, pull the har-
ness downwards until the fabric ring is turned inside out
(Fig. 23-23A).
WARNING: At the end of assembly, make sure that the
plastic slots are properly assembled. Check that the plastic
slots, once assembled on the relative safety harness buckle
forks, feature the relative horizontal protruding parts facing
the seat's exterior (fig. 23B-23C).
Once assembled, the belts must be adjusted once again
according to the size of your child.
CONVERTING THE SEAT: SOFT CARRYCOT CONFIGU-
RATION
To transform the seat, follow the steps below:
24. Unfasten the buckles located under the seat (fig. 24 –
24A).
25. Position the foot rest horizontally, adjust the back rest in
the lowest position (Fig. 25), recline the seat by pressing
the buttons shown in Fig. 14, and bring the pram into
the horizontal position.
Then remove the safety belts (see paragraph REMOVE
SAFETY BELTS).
26. WARNING: The carrycot must be used only in horizon-
tal position (Fig. 26). Do not adjust the carrycot when
inclined (Fig 26A).
27. To introduce the fabric lining, fasten it to the fabric of the
stroller by using the internal zip (Fig. 27) located in the
child's head area.
28. Then wrap the elastic part of the fabric lining around
the tube of the structure in the foot area (Fig. 28). Lastly,
fasten the press stud buttons positioned on both sides
(Fig. 28A).
WARNING: In soft carrycot configuration, do not remove
the seat from the stroller when the child is inside it.
CONVERTING THE SEAT: SEMI-RIGID CARRY COT CON-
FIGURATION
WARNINGS
IMPORTANT - READ THE INSTRUCTIONS CAREFULLY
BEFORE USE AND KEEP THEM FOR FUTURE
REFERENCE.
• Please refer to the instructions booklet before using the
stroller.
• WARNING: This product is only suitable for a child who
cannot sit up unaided. Maximum weight of the child: 9 kg.
• Indicative age of use: 0 – 5/6 months.
• WARNING: Only use on a firm ground, which is horizon-
tal, level and dry.
• WARNING:Do not let other children play unattended
near the carry cot.
• WARNING: Do not use if any part of the carrycot is bro-
ken, torn or missing.
• WARNING: Never leave your child unattended.
• WARNING: Never use this product on a stand.
• Only use spare parts supplied or approved by the man-
ufacturer.
• Do not fit to the carrycot any accessories, spare parts or
components not supplied or approved by the manufac-
turer. Any unauthorised modifications made to the prod-
uct will relieve the manufacturer of all responsibility.
• Always be aware of the risk of open fires and other sources
of heat, such as electric stoves, gas stoves etc. Never leave
the carrycot in the vicinity of such heat sources.
• Check regularly the handles and bottom of the carry cot
in order to notice any possible damage or wear and tear.
in particular, the carrying handle and the bottom of the
carrycot. Should any damage or signs of wear and tear be
noticeable, do not use the product and keep out of reach
of children.
• Make sure that the handle is in the correct position for use
before transport in the carrycot.
• In the carrycot your child's head must never be lower than
their body.
• WARNING: If you purchase a mattress to add to the inter-
nal lining separately, make sure it is suitable for the prod-
uct. Dimensions: L. 780 mm, W. 300 mm, H. 20mm. Do not
add another mattress on the upper part of the mattress of
the size recommended by the manufacturer.
• Before assembly, ensure that the product and its compo-
nents have not been damaged during transportation. In
this case, do not use and keep out of reach of children.
• Do not leave anything inside the carrycot that might re-
duce its depth.
• Keep the plastic bags away from children to prevent chok-
ing hazards.
• Products left in the sun will overheat; leave them to cool
down before placing your child in.
• The carrycot is not designed for children to sleep in for
long periods of time: this product is not a substitute for
a cot.
• When folded, store the carrycot away from children.
The Fully seat can be used as a semi-rigid carrycot with the
supplied base. To transform the semi-rigid carrycot, follow
the steps below.
Release the buckles under seat as described in step 24, and
position the seat horizontally.
In semi-rigid carrycot configuration, remove the safety
belts (see paragraph REMOVE SAFETY BELTS).
29. Open the base of the semi-rigid carrycot positioning it
horizontally until you hear the locking click (Fig. 29 – 29 A).
30. Position the base for the semi-rigid carrycot inside the
seat making sure to insert support "A" in the relevant slot
in the area of the child's head on the structure (fig. 30
– 30 A). Then close the support "B" around the tube in
the area of the feet (Fig. 30B) and fasten the two side
supports in the relevant joints. To mount the side sup-
port, rotate the central lever counter-clockwise holding
it against the joint and release it to complete coupling
(Fig. 30C). Repeat this operation on the other support.
21