Cleaning And Maintenance - Black and Decker PAD1200 Manual De Instrucciones

ENGLISH
Use
Connecting to a power source using the 12 Vdc
accessory plug (fig. C and D)
Note: The tip of the plug is positive (+) and the side contact
is negative (-).
Remove the 12 Vdc accessory plug (12) from the
storage recess (13) on the base of the appliance.
Unclip the cord clip (14) from the cord storage.
Fully unwind the cord from the cord storage (15).
Connect the appliance to the power source by inserting
the 12 Vdc accessory plug (12) firmly into the accessory
outlet of a vehicle or other dc power source.
Note: On some vehicles the accessory socket may only
become live when the ignition key is in the accessory
position.
Warning! Do not use with positive ground electrical
systems, (i.e older vehicles).
Warning! A reverse polarity connection will result in a blown
fuse and may cause permanent damage to the appliance.
When you have finished using the appliance:
Remove the 12 Vdc accessory plug (12) from the
12 Vdc source.
Wind the cord onto the cord storage (15) and secure
with the cord clip (14).
Store the 12 Vdc accessory plug (12) in the storage
recess (13) in the base of the appliance.
Switching on and off
To switch the appliance on, slide the on/off power
switch (1) to the right.
To switch the appliance off, slide the on/off power
switch (1) to the left until it clicks into the off position.
The appliance can be used for periods of up to 30 minutes
without noticeably affecting the power of a normally charged
car battery in good condition.
Warning! Extended use will drain the battery power. Do not
run the vehicle's engine while cleaning as this can shorten
the life of the appliance.
Vacuuming
When operating the appliance, make sure that the hose
is not trapped, twisted or blocked.
The handle (2) can be easily removed from the
appliance allowing you to reach up to 1.5 m from the
appliance.
With the handle (2) removed, the appliance can be
carried using the built-in handle.
The handle (2) can also be removed from the hose (4)
so that you can connect an accessory directly to the
hose cuff (11) when required.
4
Hints for optimum use
When vacuuming stairs, always start at the bottom and
work your way up.
Optimising the suction force
In order to keep the suction force optimised, the filters must
be cleared regularly during use.
Turn the filter cleaning wheel (5) two turns clockwise to
remove any dust from the filters.
The fine particulate filter must be cleaned regularly, see
"Cleaning the fine particulate filter" section.

Cleaning and maintenance

Your Black & Decker tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
care and regular cleaning.
Warning! Before performing any maintenance or cleaning
on the appliance, unplug the appliance.
From time to time wipe the appliance with a damp cloth. Do
not use any abrasive or solvent-based cleaner. Do not
immerse the appliance in water.
Emptying the dust container (fig. E)
The dust container must be emptied regularly, preferably
after every use.
Release the door latch (7) and open the transparent
door (6) 180° until it clicks in the open position.
Remove the pre-filter (16).
Empty the dust container.
Clean the pre-filter (16) by lightly shaking over a
dustbin.
Refit the pre-filter (16)
Close the transparent door (6) and make sure that it
clicks into place.
Warning! Do not, under any circumstances, rinse out the
dust container.
Warning! Do not immerse the appliance in water. A damp
cloth and soapy water should be used to clean the exterior
of the appliance. Always make sure that the appliance is
completely dry before re-use or storing.
Cleaning the fine particulate filter (fig. F)
The fine particulate filter (17) prevents particles and larger
objects from entering the motor housing.
The filter (17) is re-usable and should be cleaned regularly.
Remove the pre-filter (16) from the appliance as
described above.
Remove the fine particulate filter (17) by pulling firmly.
Tap the filter vigorously to remove loose dust from the
filter.