Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

2013 THD.com
Outdoor Snowflake Sculpture Instruction Sheet (English)
Date: 5/31/13
Model No. 7407097 / 7407098
ASSEMBLY INSTRUCTIONS:
NOTE: No tools required.
NOTE: Retain carton for storage.
1. Carefully remove assembled snowflake from the carton. Your snowflake
should include the following (Fig 1):
1 Snowflake completely assembled (plug attached)
Replacement LED bulbs and covers
Fig 1
2. Check the item for any loose, unlit or damaged bulbs. Although it will
still operate, the bulbs must be replaced promptly to ensure the
performance and life expectancy of the item.
LED replacement:
Before changing LEDs, make sure set is unplugged.
Step 1: Grasp plug and remove from the
receptacle or other outlet device.
Do not unplug by pulling cord.
Step 2: Unscrew plastic cover from LED socket.
Step 3: Hold LED lamp by the plastic base and
pull LED/base straight out of the socket.
Step 4: Replace LED with only 3 volt, 20 mA
LED type lamp (provided with product).
Step 5: Place the plastic cover over the LED
lamp and screw it back onto the socket.
Actual LED cover may vary according to product purchased.
3. To illuminate, fully insert the plug into a working GFCI outlet or an
outdoor rated extension cord.
The snowflake is now ready to hang on a flat surface by the eyelet
at the top of the snowflake frame (Fig 2).
8"
LED13
Snowflake completely assembled
Replacement LED
bulbs and covers
COVER
COVER
COVER
COVER
BASE
BASE
SOCKET
LED
SOCKET
Fig 2
TROUBLESHOOTING
1. Unplug the item and check to see that the GFCI outlet is functioning.
2. Unplug the item and check all light string connections. This product
uses low voltage coaxial connections. To connect the light strings,
align the flat ends of both connectors as shown and connect them
together. Slide the screw cover from the "male" connector over the
"female" connector and tighten (Fig 3).
Fig 3
MAINTENANCE
This outdoor sculpture includes replacement bulbs and caps for
any replacements that you need to perform on your sculpture. If
extra parts are needed, contact the Customer Service Team at
1-877-527-0313.
STORAGE INSTRUCTIONS
1. Leave assembled if storage room permits or disassemble, placing
all components in the original carton.
2. Store in cool, dry location away from sunlight.
NOTE: DO NOT USE A DIMMER SWITCH OR INSTALL ANY
ADDITIONAL CHRISTMAS LIGHTING OR ORNAMENTATION THAT IS
POWERED BY A LIGHT BULB SOCKET. DOING THIS MAY RESULT IN
DAMAGE TO THIS PRODUCT OR CAUSE PERSONAL INJURY. THIS
ACTION WILL RESULT IN A VOID OF THE LIMITED WARRANTY OF
THIS PRODUCT.
This product was pre-tested before shipment and date coded. In
keeping with the National Electric Code, this product is intended
for seasonal (90 days max.) installation and use. For problems or
questions on this product call Home Depot customer service
toll-free at 1-877-527-0313.
Made in China
Printed in China
This is not a toy, for decorative use only.
DISTRIBUTED BY HOME DEPOT U.S.A., INC. 2455
PACES FERRY RD., N.W. Atlanta, GA 30339 All rights reserved.
11.5"

Publicidad

loading

Resumen de contenidos para Home Accents Holiday 7407097

  • Página 1 Outdoor Snowflake Sculpture Instruction Sheet (English) Date: 5/31/13 8” LED13 Fig 2 Model No. 7407097 / 7407098 ASSEMBLY INSTRUCTIONS: NOTE: No tools required. NOTE: Retain carton for storage. 1. Carefully remove assembled snowflake from the carton. Your snowflake should include the following (Fig 1):...
  • Página 2 Outdoor Snowflake Sculpture Instruction Sheet (Spanish) Date: 5/31/13 8” LED13 Fig 2 Modelo N° 7407097 / 7407098 INSTRUCCIONES PARA ENSAMBLAJE: NOTA: No se requieren herramientas. NOTA: Conserve el embalaje para el almacenamiento. 1. Quite cuidadosamente el copo de nieve del embalaje. El copo de nieve...

Este manual también es adecuado para:

7407098