Lutron Electronics PK2-2B Manual De Instrucciones

Pico Wireless Control
English
3 V- 10 mA
Mounting accessories sold separately.
For a complete listing of Pico wireless mounting accessories
and more information about Pico wireless controls, please visit
www.lutron.com/pico
PK2-2B PM2-2B PN2-2B PQ2-2B
PK2-2BRL PM2-2BRL PN2-2BRL PQ2-2BRL
PK2-3B PM2-3B PN2-3B PQ2-3B
PK2-3BRL PM2-3BRL PN2-3BRL PQ2-3BRL
P/N 040430 Rev. B
LUTRON 02/2018
Important Notes
Please Read Before Installing
1. This install guide provides simple setup instructions for PowPak
systems only. If you are using your Pico wireless control with any other
Lutron system, please refer to the system setup guide. If you no longer
have your system setup guide, please download the latest version by
following the links at www.lutron.com
2. The Pico wireless control uses one (1) CR2032 battery (pre‑installed).
DO NOT use rechargeable batteries. Using improper batteries could
damage the Pico wireless control. DO NOT dispose of the battery
in normal household waste. Please recycle, take to a proper battery
disposal facility, or contact your local waste disposal provider regarding
local restrictions on the disposal or recycling of batteries.
Light
WARNING: Risk of fire, explosion and burns. May result in
serious injury or death. DO NOT recharge, disassemble, crush,
puncture, heat above 100 °C (212 °F) or incinerate the battery.
The battery in this device contains Perchlorate Material —
special handling may apply. For more information, visit
www.dtsc.ca.gov/hazardouswaste/perchlorate
3. The Pico wireless control must be paired with dimmer(s) / switch(es)
before it can communicate.
4. Up to 10 Pico wireless controls can be configured to work together with
a stand‑alone PowPak module.
5. The range of the Pico wireless control is 9 m (30 ft). Performance is
highly dependent on a variety of complex factors, such as:
• Distance between system components
• Geometry of the building structure
• Construction of walls separating system components
• Electrical equipment located near system components
6. Clean Pico wireless control with a soft damp cloth only. DO NOT use
any chemical cleaners.
7. DO NOT paint the Pico wireless control.
8. DO NOT mount the Pico wireless control to a metal surface.
CE Information
(For model numbers PK2‑, PQ2‑)
Lutron Electronics hereby declares that the model numbers listed above are
in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC. A copy of the DoC can be obtained by writing to:
Lutron Electronics Co., Inc. 7200 Suter Road, Coopersburg, PA 18036 U.S.A.
ImDA Compliance Information
(For model number PM2‑)
Complies with
ImDA standards
DA 103083
TRA
Light
REGISTERED NO:
ER61252/18
DEALER NO:
0016561/08
Lutron EA Limited
125 Finsbury Pavement
4th floor, London EC2A 1NQ
United Kingdom (Importer)
Set-Up
(for PowPak systems only)
To communicate with other systems or devices, including RA 2,
GRAFIK Eye QS, HomeWorks QS, QS sensor module (QSM),
Quantum, myRoom, Serena Shades, Vive, and Sivoia QS, refer to the
system setup guides.
Important: Set up a Pico wireless control to a load control
before use.
1. On the PowPak dimming module, hold the Toggle button " " for
6 seconds until lights flash (Figure 1).
The load status LED will begin flashing twice per second.
2. Press and hold the Off button on the Pico wireless control (Figure 2)
until the load status LED on the module and the load flash 3 times
(approximately 6 seconds).
3. Repeat step 2 to pair multiple Pico wireless controls with a single
PowPak dimming module. Repeat steps 1– 2 to pair a single Pico
wireless control with multiple PowPak dimming modules.
4. On the PowPak dimming module, hold the Toggle button " " for
6 seconds to save the association. Loads will flash and LED will quickly
blink for 2 seconds.
Figure 2
Figure 1
Power
Pico
PowPak Module
Wireless Control
Replacing the Battery in a Pico Wireless Control
1. Place a flathead screwdriver into the slot at the bottom of the Pico
Light wireless control. Twist to open. DO NOT press buttons without back Shade
enclosure on.
2. Slide the battery out, toward the top of the Pico wireless control.
3. Slide a new battery underneath the contact strap, with the (–) terminal
On Open
toward the front of the Pico wireless control.
4. Replace the back enclosure.
5. Confirm proper installation by turning the receiving device ON and OFF
using the Pico wireless control.
O Close
Shade
)Lutron, Lutron, HomeWorks, PowPak, Pico, Vive, Quantum, GRAFIK Eye, Serena, and Sivoia are trademarks of Lutron Electronics Co., Inc. registered in the U.S. and other countries.
myRoom and RA2 are trademarks of Lutron Electronics Co., Inc.
© 2017‑2018 Lutron Electronics Co., Inc.
Operation
Indicator LED
Flashes to indicate a button
press or when unit is in
programming mode.
Preset Button
(3B & 3BRL models only)
Tap once:
Devices go to preset
levels / positions. Activates
scene 16 when used in scene
mode with GRAFIK Eye QS
wireless applications.
Press and hold:
To save new preset level or
position, press and hold
for 6 seconds.
Shade Drape
Un-pairing a Pico Wireless Control
To un‑pair a previously paired Pico wireless control from your system perform the following
steps:
1. Quickly tap the OFF button, Figure 2, on the Pico wireless control
3 times and continue to hold it for 6 seconds after the third tap.
2. Once the indicator LED comes on solid, quickly tap the OFF button 3 times. Do not
continue to hold on the third tap.
3. To test that the Pico wireless control has been successfully removed from the system,
press the ON button a verify that the Pico wireless control no longer controls the load.
NOTE: This will remove all dimmers / switches with which it was previously paired.
Shade 1 Shade 2
Open Open
Troubleshooting
Symptoms
Close Close
Light does not respond to Pico wireless
control.
When in set‑up mode, the LEDs on the
dimmer / switch flash when trying to set up
Shade 1 Shade 2
with the Pico wireless control or sensor.
Top Button
Lights brighten to full intensity and shades /draperies go to
open limit. Activates scene 1 when used in scene mode with
GRAFIK Eye QS wireless applications.
Raise Button (2BRL & 3BRL models only)
Lights increase in intensity and shades /draperies move
towards open limit.
Lower Button (2BRL & 3BRL models only)
Lights decrease in intensity and shades /draperies move
towards close limit.
Bottom Button
Lights dim to off and shades /draperies go to close limit.
Activates "OFF" scene when used in scene mode with
GRAFIK Eye QS wireless applications.
Customer Assistance
www.lutron.com/support
For questions concerning the installation or operation of this
product, call Lutron Customer Assistance. Please provide
exact model number when calling.
Worldwide Headquarters
USA
TEL: +1.610.282.3800
FAX: +1.610.282.1243
Screen Drape
Customer Assistance: 1.844.LUTRON1
United Kingdom
TEL: +44.(0)20.7702.0657
Open Open
FAX: +44.(0)20.7480.6899
Customer Assistance: +44.(0)20.7680.4481
FREEPHONE: 0800.282.107
Singapore
TEL: +65.6220.4666
FAX: +65.6220.4333
Customer Assistance: 800.120.4491
Possible Causes
Close Close
• The dimmer / switch failed to pair with Pico wireless control; see Set-Up.
• The dimmer / switch has already received and responded to a command or is already at the light
setting the Pico wireless control is sending.
• The Pico wireless control is outside the 9 m (30 ft) operating range.
• The battery in the Pico wireless control is low.
• The battery in the Pico wireless control is installed incorrectly.
• The maximum number of Pico wireless controls or sensors has been paired with the
dimmer / switch. More Pico wireless controls or sensors cannot be added. See Un-pairing a
Screen Drape
Pico Wireless Control.
Blackout
Open
Close
Blackout S
®