Publicidad
Idiomas disponibles
Idiomas disponibles
EN GLI SH
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor
size is 1 mm
; the maximum length is 30 m.
2
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Inserting and Removing a Cutter
(fi g. 2)
1. Press and hold down the spindle lock (j).
2. Using the 22 mm wrench, loosen the collet nut
(i) a few turns and insert a cutter (p).
3. Tighten the collet nut and release the spindle
lock (j).
WARNING: Never tighten the collet nut
without a cutter in the collet.
Replacing the Collet Assembly
(fi g. 3)
This tool is supplied with 1/4" and 1/2" collets. Other
precision collets are also available as an option to
suit the cutter used. The collet and the collet nut are
inseparable.
1. Loosen the collet nut (i) completely.
2. Remove the collet assembly (q).
3. Fit a new assembly and tighten the collet nut.
Setting the Electronic
Speed Control Dial (fi g. 1)
The speed is infinitely variable from 8,000 to 21,000
min-1 using the electronic speed control dial (c) for
uniform cutting results in all types of wood, plastics
and in aluminium.
28
– Turn the electronic speed control dial to the
required level. The correct setting, however, is a
matter of experience.
Generally, use the low setting for large diameter
cutters and the high setting for small diameter
cutters.
1 = 8,000 min
-1
2 = 9,800 min
-1
3 = 11,900 min
-1
4 = 14,100 min
-1
5 = 16,400 min
-1
6 = 18,800 min
-1
7 = 21,000 min
-1
Adjusting the Depth of Cut
QUICK ADJUSTMENT USING THE GRADUATION (FIG. 4)
1. Loosen the plunge lock (r).
2. Loosen the depth stop locking bolt (m).
3. Lower the router carriage until the cutter is in
contact with the workpiece.
4. Tighten the plunge lock (r).
5. Adjust the depth of cut by moving the depth
stop adjuster (n) to zero on the graduation (o).
6. Lift the depth stop (l) until the pointer shows the
desired depth of cut on the graduation (o).
7. Tighten the depth stop locking bolt (m).
8. Loosen the plunge lock (r).
MULTIPLE DEPTH ADJUSTMENT USING
THE REVOLVER DEPTH STOP (FIG. 4)
The revolver depth stop (k) can be used in 5 different
depths. This is particularly useful for deep cuts,
performed in steps.
– Place a depth template between the depth stop
(l) and the revolver depth stop (k) to adjust the
exact cutting depth.
If required, use all five depths. For two positions, a
set screw is available.
FINE ADJUSTMENT (FIG. 4)
When not using a depth template, or if the depth of
cut needs readjustment, it is recommended to use
the fine adjuster (s).
– Adjust the depth of cut using the fine adjuster
(s). One turn corresponds to approx. 1 mm.
Limiting the Plunge Stroke (fi g. 4)
For optimum convenience, the quick-release
adjustment nut (t) can be used to adapt the plunge
stroke to the adjusted depth of cut.
Publicidad
