Instruction Sheet - Vimar Idea 16573 Hoja De Instalación

Idea
16573
Electronic alarm clock, supply voltage 120-230 V~ 50-60 Hz - 3 modules.
IMPORTANT!
Remove the protective
film to activate the buff-
er battery only on deliv-
ery and activation of the
system.
DESCRIPTION.
Switch with integrated calendar and thermometer, suitable
for installation near a headboard in a normal flush mounting,
surface mounting or table mounting boxes.
CHARACTERISTICS.
• Supply voltage: 120-230 V~ 50-60 Hz
• Average absorption: 1 VA
• Front controls: "Esc", "", "", "ok"/"set"
• CLOCK function
• ALARM function with choice of 3 alarm sounds.
• THERMOMETER function with indication in °C.
• Clock backup battery duration: 10 days, with type CR2032
battery
• Timed back-lit display, activated by pressing one of the four
push buttons.
• Multilingual menu: Italian, English, French, Spanish and
German.
• Protection degree: IP40
• Class II equipment:
• Possibility of protection against removal using the screw
provided.
• Can be installed in a box with minimum depth of 46 mm.
• Operating temperature: 0 °C +40 °C
• Ambient temperature range during transport: -25 °C +60 °C
• Clock accuracy: less than 30 s a month
OPERATION.
To set the electronic alarm clock, from the starting screen of
the display:
• Press any one of the front buttons.
• The "Alarm Set" menu item appears, and the following icons
are displayed:
- "Esc" (button A): return to the preceding screen.
- "" (button B): scroll down the settings or menus.
- "" (button C): scroll up the settings or menus.
- "ok" (button D): proceed to the next screen.
- "set" (button D): confirm the entered value.
• Press "" (button B) to invoke the "Settings" menu item.
Protection against removal.
Screw for protection against removal,
on the rear of the switch
Viale Vicenza, 14 - I 36063 Marostica VI
Tel. +39 0424 488 600 - Fax (Export) +39 0424 488 709
www.vimar.eu
SET ALARM.
Used for setting "Alarm ON" or "Alarm OFF".
• Alarm ON: turn on the alarm and program the alarm time.
• Alarm OFF: turn off the alarm.SETTINGS.
Used for setting the "Clock", "Date", "Alarm Sound",
"Display", "Language", "Mode".
• Clock: set the current time (hours and minutes).
• Date: set the current date (date, month, year).
• Alarm Sound: set the alarm tone, from a choice of three
possible alarm sounds.
• Display: adjust the contrast of the display.
• Language: cselect the language in which the instructions
are displayed, choosing between Italiano, English, Français,
Español and Deutsch.
• Mode: select the principal display mode, choosing between:
- current date and time.
- temperature, current date and time.
INSTALLATION RULES.
The installation must be done according to rules for electri-
cal installations of buildings in force in the country where the
products are installed.
CONFORMITY TO STANDARDS.
LV Directive
Standard EN 60065
EMC Directive
Standards EN 61000-6-1, EN 6100-6-3
Electrical diagram.
L
N
Hole for protection against removal,
on the rear of the switch

Instruction sheet

Front view and view of controls.
A B C D
Items of the
scrolling menu
"Esc". "ok".
Confirm
Return to the
the entered value
preceding screen.
or proceed
to the next screen.
" ". " ".
Downward scrolling Upward scrolling
of settings or menus. of settings and menus.
Replacing the battery.
CR2032
ATTENTION.
• The CR2032 backup battery allows the alarm clock to be
programmed even when the switch is removed from its
mounting box.
• In the event of a power outage, the CR2032 backup bat-
tery guarantees continued operation of the display, and
updating of the date and time, for a minimum of 10 days.
However it does not allow the alarm clock function to
be used.
The buffer battery is required in order for the equipment
to function properly.
ATTENTION!
After replacing the battery, dispose of the old battery
in the appropriate sorted refuse bins.
ENGLISH