Zwave enbrighten ZW3012 Manual De Instrucciones

FCC/IC
En
This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS
standards. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modifications to this equipment. Such modifications could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions may cause harmful interference to radio
communications. However, there is no guarantee interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different to which the receiver is
connected.
— Consult the dealer or an experienced radio/TV technician for help
Important note: To comply with the FCC RF exposure compliance requirements, no change
to the antenna or the device is permitted. Any change to the antenna or the device could
result in the device exceeding the RF exposure requirements and void user's authority to
operate the device.
Fr
Cet appareil est conforme au paragraphe 15 des normes FCC et au CNR pour les appareils
exempts de licence d'Industrie Canada. Son utilisation est sujette aux deux conditions
suivantes : (1) cet appareil ne doit pas occasionner de brouillage préjudiciable et (2) cet
appareil doit accepter toutes les interférences reçues, notamment les interférences qui
peuvent provoquer un fonctionnement non désiré.
NOTE DE LA FCC : Le fabricant n'est pas responsable des interférences sur les fréquences
radioélectriques ou télévisuelles pouvant être causées par des modifications non autorisées
de ce matériel. De telles modifications peuvent annuler le droit de l'utilisateur à utiliser cet
appareil.
REMARQUE : Cet appareil a été testé et certifié conforme aux limites relatives aux appareils
numériques de catégorie B définies dans le paragraphe 15 des normes FCC. Ces limites ont
été définies afin de fournir une protection raisonnable contre le brouillage préjudiciable
en milieu résidentiel. Cet appareil produit, utilise et peut émettre des ondes de fréquence
radio et, s'il n'est pas installé et utilisé conformément aux instructions, il peut provoquer
un brouillage préjudiciable aux communications radio. Il n'existe toutefois aucune garantie
que des interférences ne se produiront pas au sein d'une installation donnée. Si cet appareil
occasionne un brouillage préjudiciable à la réception radiophonique ou télévisuelle, il suffit
d'allumer et d'éteindre l'appareil pour déterminer sa responsabilité. Nous encourageons
l'utilisateur à essayer de corriger ces interférences en appliquant une ou plusieurs des
mesures suivantes :
— Réorienter ou déplacer l'antenne de réception.
— Augmenter la distance entre l'appareil et le récepteur.
— Brancher l'appareil à une prise secteur différente de celle du récepteur.
— Consulter le revendeur ou un technicien spécialisé en postes radio ou téléviseurs.
Remarque importante : Pour se conformer aux exigences de conformité de la FCC
concernant l'exposition aux RF, aucune modification apportée à l'antenne ou au dispositif
n'est autorisée. Toute modification apportée à l'antenne ou au dispositif pourrait faire en
sorte que le dispositif dépasse les exigences d'exposition aux RF et pourrait annuler le droit
de l'utilisateur à utiliser ce dispositif.
Es
Este dispositivo cumple con las Especificaciones del apartado 15 de las normas de la FCC
y con las especificaciones de las normas radioeléctricas (RSS) del Ministerio de Industria
de Canadá aplicables a aparatos exentos de licencia. El funcionamiento está sujeto a las
siguientes dos condiciones: (1) este dispositivo no debe provocar interferencia perjudicial,
y (2) este dispositivo debe aceptar toda interferencia que reciba, incluso la que pudiera
causar un funcionamiento no deseado.
NOTA DE LA FCC: El fabricante no se hace responsable de ninguna interferencia de radio
o TV ocasionada por modificaciones no autorizadas efectuadas a este equipo. Dichas
modificaciones podrían anular la autoridad del usuario para utilizar el equipo.
NOTA: Este equipo ha sido probado y cumple con los límites para aparatos digitales de
Clase B, de conformidad con el apartado 15 de las normas de la FCC. Estos límites están
diseñados para proveer protección razonable contra interferencias perjudiciales en una
instalación residencial. Este equipo genera, usa y puede irradiar energía de radiofrecuencias
y, si no se instala y usa según las instrucciones, puede provocar interferencia perjudicial a
las radiocomunicaciones. No obstante, no hay garantías de que no ocurrirá interferencia en
una instalación en particular. Si este equipo provoca interferencia perjudicial a la recepción
de radio o televisión, lo que puede determinarse encendiendo y apagando el equipo, se
recomienda que el usuario intente corregir la interferencia por medio de la implementación
de una o más de las siguientes medidas:
— Reorientar o reubicar la antena receptora.
— Incrementar la separación entre el equipo y el receptor.
— Conectar el equipo a un tomacorriente de un circuito diferente del circuito al que está
conectado el receptor.
— Consultar al distribuidor o a un técnico con experiencia en radio/televisión para
solicitar asistencia.
Nota importante: Para cumplir con los requisitos de cumplimiento de exposición de
radiofrecuencia de la FCC, no se permiten cambios a la antena o el dispositivo. Cualquier
cambio a la antena o dispositivo podría hacer que el dispositivo supere los requerimientos
de exposición de radiofrecuencia y anular la autoridad del usuario para operar el
dispositivo.
Responsible Party - US Contact Information | Parte responsable - Información de
contacto de los Estados Unidos | Partie responsable - Coordonnées des États-Unis
FCC ID — U2ZZW3012 | IC: 6924A-ZW3012
Jasco Products Company | Model: ZW3012/52252
10 E. Memorial Rd., Oklahoma City, OK 73114 | 1-800-654-8483
CAN ICES-3(B)/NMB-3(B)
All brand names shown are trademarks of their MADE IN CHINA/FABRIQUÉ EN CHINE/HECHO EN CHINA
respective owners.
DISTRIBUTED BY JASCO PRODUCTS COMPANY LLC,
T ous les noms de marque illustrés sont des marques
10 E. MEMORIAL RD., OKLAHOMA CITY , OK 73114.
de commerce de leurs propriétaires respectifs.
©JASCO 2020 | 52252 | ZW3012 | 10/20/20 v1
T odas las marcas que aparecen aquí son marcas
registradas de sus respectivos dueños.
1.
Tools you will need
IMPORTANT!
Confirm bulb is dimmable and in working order, switch is not functional
without complete circuit.
Getting to know your new Z-Wave device
• No neutral wire required
• Turn ON/OFF and adjust dim levels manually or remotely via the Z-Wave
controller
• May be used in single-pole installation or with up to four add-on switches
(model 46199) in 3-way or 4-way wiring configurations
• Compatible with all incandescent and most dimmable CFL/LED bulbs
• Interchangeable paddle switch — white & light almond paddle in package
• Uses a standard, rocker-style wallplate for single-gang installations
(wallplate not included)
• Blue LED indicates dimmer location in a dark room
• Z-Wave certified for simple pairing and integrated home automation
• Screw terminal installation — requires wiring connections for line (hot), load,
and ground. Traveler wire required for 3-way or 4-way installation
• This Z-Wave device has advanced features that allow you to customize
your experience. These features can only be adjusted by a Z-Wave enabled
controller that supports the Z-Wave configuration command class. For a
complete list of adjustable configurations, visit www.ezzwave.com/config
2.
A
E
B D
F
C
A. Ground (Green/Bare) E. Top rocker — press & release
to turn dimmer ON, press &
B. Line or Load (Black)
hold increases brightness
C. Line or Load (Black)
F. Bottom rocker — press
D. Traveler (Red/Other) & release to turn dimmer
OFF, press & hold to dim
MANUAL • MANUEL • MANUAL
In-Wall No-Neutral
READ IT OR WATCH IT
Smart Dimmer
Gradateur intelligent
sans neutre mural
Read instructions or watch easy-to-follow video.
Scan QR code or visit https://byjasco.com/52252i.
Atenuador de luz
inteligente para pared
sin neutro
Convert any smart control* to a multi-location switch
*For a list of compatible devices, visit ezzwave.com
Smart Control Add-on Switches
To purchase an add-on switch or for more
details, visit ezaddonswitch.com.
Multiple Paddle
Colors Available
ezzwave.com/paddlecolors
Purchase additional items at
ezzwave.com or visit your local retailer.
In-Wall Plug-in
Smart Dimmers Smart Dimmers Add-on Switches
In-Wall Motion
Plug-in
Switch or Dimmer Smart Switches Smart Switches
Enbrighten In-Wall Hinge Pin
Smart LED Bulb Smart Fan Control Smart Door Sensor
Direct Wire, Portable In-Wall
40A Outdoor Smart Multi Tamper-Resistant Outdoor Smart
Smart Switch Sensor Smart Outlet
3. 3.
OR
OR
WARNING — SHOCK HAZARD
Turn OFF the power to the branch circuit for the dimmer and lighting fixture at
the service panel. All wiring connections must be made with the POWER OFF
to avoid personal injury and/or damage to the dimmer.
This device is intended for installation in accordance with the National Electric
Code and local regulations in the United States or the Canadian Electrical Code
and local regulations in Canada. If you are unsure or uncomfortable about
performing this installation, consult a qualified electrician.
Multi-switch wiring
For 3-way installations, please refer to add-on switch (46199) manual.
Single-switch wiring
Before installation, you may wish to change the paddle color to match your wallplate or décor.
Please proceed to section 5.
1. Shut off power to the circuit at circuit breaker or fuse box.
IMPORTANT! Verify power is OFF to switch box before continuing.
2. Remove wallplate.
3. Remove the switch mounting screws.
4. Carefully remove the switch from the switch box. DO NOT disconnect the wires.
5. There are four screw terminals on the dimmer marked:
A. GROUND — Green/Bare
B. LINE OR LOAD — Black (connected to power or lighting)
C. LINE OR LOAD — Black (connected to power or lighting)
D. TRAVELER — Red/Other (only in 3-way installations)
Match these screw terminals to the wires connected to the existing switch.
6. Disconnect the wires from the existing switch. Label wires according to the previous terminal
connection.
4.
Adding your device to a Z-Wave network
1. Follow the instructions for your Z-Wave certified controller to add
a device to the Z-Wave network.
2. Once the controller is ready to add your device, press and release
the top or bottom of the smart dimmer (rocker).
You have complete control to turn your fixture ON/OFF according to
groups, scenes, schedules and interactive automations programmed
by your controller.
If your Z-Wave certified controller features remote access, you can
control your fixture from your mobile devices.
If prompted by the controller to enter the S2 security code, refer to
the QR code/security number on the side of the box or the QR code
label on the product (see Figure 1). Enter the 5-digit pin code.
Figure 1:
DO NOT RETURN THIS
PRODUCT TO THE STORE
STOP
NE RETOURNEZ PAS
CE PRODUIT AU MAGASIN
NO DEVUELVA ESTE
PRODUCTO A LA TIENDA
If you have any problems or questions, contact our U.S.-based Consumer Care at
1-800-654-8483, option 1, Monday–Friday, 7AM–8PM Central Time.
For the most up-to-date product support, accessories, electronic (PDF) format
manuals and more, visit www.byjasco.com/support.
• No user-serviceable parts in this unit.
Si vous avez des problèmes ou des questions, veuillez communiquer avec notre
service à la clientèle aux États-Unis au 1-800-654-8483, option 1, du lundi au
vendredi, de 7 h à 20 h heure du Centre.
52252
Pour un soutien technique d'avant-garde, les nouveaux accessoires, les plus
ZW3012
récents manuels en format électronique (PDF) et plus encore, visitez le site
www.byjasco.com/support.
• Aucune des pièces de ce dispositif ne peut être réparée par l'utilisateur.
Si tiene problemas o dudas, comuníquese con nuestro Centro de atención al
cliente con sede en EE. UU. al 1-800-654-8483, opción 1, de lunes a viernes, de 7
a.m. a 8 p.m., hora del Centro.
Para recibir el soporte técnico más actualizado sobre productos, accesorios,
manuales en formato digital (PDF), entre otros, visite www.byjasco.com/support
• Esta unidad no contiene piezas que el usuario pueda reparar.
WARNING
RIESGO DE INCENDIO
RISK OF FIRE
RIESGO DE DESCARGA ELÉCTRICA
RISK OF ELECTRICAL SHOCK
RISK OF BURNS RIESGO DE QUEMADURAS
CONTROLLING APPLIANCES CONTROL DE EQUIPOS ELECTRODOMÉSTICOS
PRECAUCIÓN:
CAUTION:
A FIN DE DISMINUIR EL RIESGO DE
TO REDUCE THE RISK OF OVERHEATING AND
POSSIBLE DAMAGE TO OTHER EQUIPMENT, DO RECALENTAMIENTO Y DE POSIBLES DAÑOS EN LOS
NOT INSTALL TO CONTROL A RECEPTACLE, DEMÁS EQUIPOS, NO INSTALAR PARA CONTROLAR
UN RECEPTOR, UN APARATOS QUE FUNCIONAN
MOTOR-OPERATED APPLIANCE, FLUORESCENT
A MOTOR, ARTEFACTOS DE ILUMINACIÓN DE LUZ
LIGHTING FIXTURE OR TRANSFORMER-SUPPLIED
FLUORESCENTE O APARATOS ALIMENTADOS CON
APPLIANCE.
• ONL Y USE TO CONTROL INCANDESCENT OR TRANSFORMADORES.
DIMMABLE CFL/LED BULBS • USAR EXCLUSIVAMENTE PARA CONTROLAR
• DO NOT EXCEED RATINGS BOMBILLAS CFL/LED INCANDESCENTES O
ATENUABLES
• DO NOT USE TO CONTROL ANY DEVICE WHERE
• NO SUPERE LOS VALORES NOMINALES
UNINTENDED OPERATION COULD CAUSE
UNSAFE CONDITIONS (HEAT LAMP, SUN LAMP, ELÉCTRICOS
ETC.) • NO USAR PARA CONTROLAR DISPOSITIVOS EN LOS
• DO NOT USE TO CONTROL RECEPTACLES QUE EL FUNCIONAMIENTO NO INTENCIONADO
PODRÍA PROVOCAR SITUACIONES PELIGROSAS
• FOR INDOOR USE ONL Y
AVERTISSEMENT (LÁMPARAS DE CALEFACCIÓN, LÁMPARAS
SOLARES, ETC.)
• NO UTILICE PARA CONTROLAR TOMACORRIENTES.
RISQUE D'INCENDIE
• USE SOLAMENTE EN INTERIORES
RISQUE DE CHOC ÉLECTRIQUE
RISQUE DE BRÛLURES
NOT FOR USE WITH MEDICAL OR LIFE-SUPPORT
COMMANDE DES APPAREILS
EQUIPMENT
ATTENTION:
Z-WAVE ENABLED DEVICES SHOULD NEVER BE USED
POUR RÉDUIRE LE RISQUE DE SURCHAUFFE ET DE
TO SUPPL Y POWER TO OR CONTROL THE ON/OFF
DOMMAGES POSSIBLES À D' A UTRES APPAREILS,
STATUS OF MEDICAL OR LIFE-SUPPORT EQUIPMENT.
NE PAS INSTALLER POUR COMMANDER
UN RÉCEPTEUR, UN APPAREIL ACTIONNÉ
NE PAS UTILISER AVEC UN ÉQUIPEMENT MÉDICAL
PAR MOTEUR, UN APPAREIL D'ÉCLAIRAGE
OU DE SURVIE
FLUORESCENT OU UN APPAREIL ALIMENTÉ PAR
LES DISPOSITIFS COMPATIBLES AVEC LA
UN TRANSFORMATEUR.
TECHNOLOGIE Z-WAVE NE DEVRAIENT JAMAIS ÊTRE
• UTILISER SEULEMENT POUR COMMANDER
UTILISÉS POUR ALIMENTER OU COMMANDER LA MISE
LES AMPOULES À DEL ET FLUOCOMPACTES À
EN MARCHE OU L' A RRÊT DE L'ÉQUIPEMENT MÉDICAL
INCANDESCENCE OU À INTENSITÉ RÉGLABLE
OU DE SURVIE.
• NE PAS DÉPASSER LES CARACTÉRISTIQUES
SE PROHÍBE SU EMPLEO EN EQUIPO MÉDICO
NOMINALES
O EQUIPO PARA EL MANTENIMIENTO DE LAS
• NE PAS UTILISER POUR COMMANDER
FUNCIONES VITALES
DES APPAREILS POUR LESQUELS UN
LOS DISPOSITIVOS Z-WAVE NUNCA SE DEBEN USAR
FONCTIONNEMENT IMPRÉVU POURRAIT
PARA SUMINISTRAR ENERGÍA ELÉCTRICA AL EQUIPO
ENTRAÎNER DES CONDITIONS DANGEREUSES
In-Wall
MÉDICO O AL EQUIPO PARA EL MANTENIMIENTO
(LAMPE À RAYONS INFRAROUGES, LAMPE
DE FUNCIONES VITALES, NI PARA CONTROLAR EL
SOLAIRE, ETC.)
ESTADO DE ENCENDIDO O APAGADO DE DICHOS
• NE PAS UTILISER POUR COMMANDER LES PRISES
EQUIPOS.
DE COURANT
• POUR UTILISATION INTÉRIEURE UNIQUEMENT
In-Wall
Plug-in
Switch
Insert wires into holes, do not wrap
wires around screws.
Do not remove screws.
B
D
A
C
Observe important wiring information
IMPORTANT! This dimmer is rated for and intended to only be used with copper wire.
Wire gauge requirements
Use 14AWG or larger wires suitable for at least 80° C for supplying line (hot), load, ground and
traveler connections.
Wire strip length
For attachment using the enclosure's holes, strip insulation 5/8in. (16mm).
UL specifies the tightening torque for the screws is 14Kgf-cm (12lbf-in).
1. Connect the green or bare copper ground wire to the GROUND terminal.
2. Connect the black wire from the light to either LINE/LOAD terminal.
3. Connect the black wire from the electrical service panel (hot) to the other LINE/LOAD terminal.
NOTE: The traveler terminal is only used for 3-way or 4-way wiring and should not be used if the
dimmer is being installed in a 2-way system (one switch & one load).
4. Insert dimmer into the switch box being careful not to pinch or crush wires.
5. Dimmer must be independently mounted (vertical position only).
6. Secure the dimmer to the box using the supplied screws.
7. Mount the wallplate.
8. Reapply power to the circuit at fuse box or circuit breaker and test the system.
Basic operation
The connected light can be turned ON/OFF and adjust dim levels in two ways:
1. Manually from the front panel of the dimmer.
2. Remotely with a Z-Wave controller.
Manual control
The front panel rocker dimmer allows the user to:
Turn ON/OFF the connected fixture.
1. T o turn the connected fixture ON, press and release the top of the rocker.
2. T o turn the connected fixture OFF, press and release the bottom of the rocker.
5.
To remove and reset the device
1. Follow the instructions for your Z-Wave certified controller to
remove a device from the Z-Wave network.
2. Once the controller is ready to remove your device, press and
release the top or bottom of the smart dimmer (rocker).
To return your dimmer to factory defaults
1. Quickly press ON (top) button three times, then immediately
press the OFF (bottom) button three times. The LED will flash
ON/OFF five times when completed successfully.
NOTE: This should only be used if your network's primary controller
Z-WAVE INTEROPERABILITY
is missing or otherwise inoperable.
This product can be added and operated
NOTE: SmartStart enabled products can be added into a Z-Wave
in any Z-Wave network with other Z-Wave
network by scanning the QR code on the product with a controller
certified devices from other manufacturers
providing SmartStart inclusion. No further action is required and the
SmartStart product will be added automatically within 10 minutes of and/or other applications. All non-battery
being switched on in the network vicinity. operated nodes within the network will
act as repeaters regardless of vendor
to increase reliability of the network.
WARRANTY
Jasco Products Company warrants this product to be free from manufacturing defects
five years from the original date of consumer purchase. This warranty is limited to the
repair or replacement of this product only and does not extend to consequential or
incidental damage to other products that may be used with this product. This warranty is
in lieu of all other warranties, expressed or implied. Some states do not allow limitations
on how long an implied warranty lasts or permit the exclusion or limitation of incidental
or consequential damage, so the above limitations may not apply to you. This warranty
gives you specific rights, and you may also have other rights which vary from state to
state. Please contact our U.S.-based Consumer Care at 1-800-654-8483 (option 1)
between 7AM – 8PM, M-F, Central Time or www.byjasco.com if the unit should prove
defective within the warranty period.
GARANTIE
Jasco Products Company garantit que ce produit est exempt de tout défaut de
fabrication pour une période de cinq ans à compter de la date de l'achat original par
l'acheteur. Cette garantie se limite exclusivement à la réparation ou au remplacement de
ce produit et n'est pas applicable aux dommages indirects ou accessoires survenus sur
d'autres produits utilisés avec ce produit. Cette garantie se substitue à toute autre
garantie expresse ou implicite. Certains États ne permettent pas de restrictions quant à la
durée d'une garantie implicite ou permettent l'exclusion ou la limitation des dommages
indirects et accessoires; il se peut, par conséquent, que cette garantie ne s'applique pas
dans votre cas. Cette garantie vous confère des droits juridiques précis; vous pouvez jouir
d'autres droits qui peuvent varier d'un État à l'autre. Veuillez communiquer avec notre
service à la clientèle aux États-Unis au 1-800-654-8483 (option 1) entre 7 h et 20 h, heure
du Centre ou par l'intermédiaire de notre site web www.byjasco.com si l'appareil s'avère
défaillant au cours de la période de garantie.
GARANTÍA
Jasco Products Company garantiza que este producto no tendrá defectos de fabricación
durante cinco años a partir de la fecha de compra del consumidor original. Esta garantía
se limita a la reparación o reposición de este producto y no cubre daños indirectos o
incidentales a otros productos que se pudieran utilizar con este producto. Esta garantía
reemplaza cualquier otra garantía explícita o implícita. Algunos estados no permiten la
aplicación de limitaciones respecto de la duración de una garantía implícita o permiten la
exclusión o limitación de la cláusula sobre daños indirectos o incidentales, por este
ADVERTENCIA motivo las limitaciones arriba mencionadas pueden no aplicarse en su caso. Esta garantía
le otorga derechos específicos y es posible que tenga otros derechos que pueden variar
según el estado en el que vive. Por favor, comuníquese con nuestro Centro de atención al
cliente con sede en EE. UU. al 1-800-654-8483 (opción 1) entre 7 y 20 h, Hora del Centro,
o a través de nuestro sitio de internet www.byjasco.com.
Jasco Products Company LLC, Building B
10 E. Memorial Rd. Oklahoma City, OK 73114.
SPECIFICATIONS
ZW3012
Power: 120VAC, 60Hz
Signal (frequency): 908.4/916MHz
Maximum loads: 1-gang 600W, 2-gang 500W or 3-gang 400W incandescent, 300W
dimmable CFL/LED
Minimum load: 8W incandescent, 5.5W dimmable CFL/LED
Range: Up to 150ft. line of sight between the wireless controller and the closest
Z-Wave receiver module
Operating temperature range: 32-104° F (0-40° C)
Type 1 enclosure, independetly mounted (vertical position only), operating control:
type 1.b action, pollution degree (2), rated impulse voltage (2500V), software class A
For indoor use only
Specifications subject to change without notice due to continuing product
improvement
SPÉCIFICATIONS
ZW3012
Tension : 120VCA, 60Hz
Signal (fréquence) : 908.4/916MHz
Charges maximales : 1 compartiments 600W, 2 compartiments 500W, 3
compartiments 400W lampes à incandescent, 300W CFL/LED dimmable
Charge minimale : 8W lampes à incandescent, 5.5W CFL/DEL dimmable
Portée : Distance à vue entre la télécommande et le module de réception Z-Wave le
plus proche allant jusqu'à 150 pi (45.7m)
Plage de températures de fonctionnement : De 32 à 104° F (de 0 à 40° C)
Boîtier de type 1, monté indépendamment (position verticale seulement), intervention
de type 1.b commande de fonctionnement, degré de pollution (2), tension de choc de
(2500V), logiciel de classe A
Utilisation intérieure uniquement
En raison d'améliorations continues du produit, les spécifications peuvent faire l'objet
de changements sans préavis
ESPECIFICACIONES
ZW3012
Alimentación: 120VCA, 60Hz
Señal (frecuencia): 908.4/916MHz
Cargas máximas: Caja para 1 conexiones 600W, caja para 2 conexiones 500W, caja
para 3 conexiones 400W sólo las lámparas incandescente, 300W CFL/LED regulable
Carga mínima: 8W sólo las lámparas incandescente, 5.5W CFL/LED regulabl
Alcance: Hasta 150 pies (45.7m) en línea de visión directa entre el control remoto
inalámbrico y el módulo receptor Z-Wave más cercano
Rango de temperatura de funcionamiento: 32-104° F (0-40° C)
Recinto de tipo 1, independientemente montado (solo en posición vertical), control de
operación: acción tipo 1.b, grado de contaminación (2), voltaje de impulso (2500V),
software de clase A
Para uso en espacios interiores solamente
Especificaciones sujetas a cambio sin aviso debido a continuas mejoras del producto
Out to Light (Load)
B
A
D
C
From Breaker Box
Adjust dim levels
1. T o increase brightness, press and hold the top of the rocker.
2. T o decrease brightness, press and hold the bottom of the rocker.
Cycle LED light
The LED below the dimmer acts as a guide light or status indicator.
How to cycle through options: Press up three times and down once quickly.
1. LED is ON when the load is OFF (guide light in the dark) (default)
2. LED is ON when the load is ON (indicates the dimmer is ON)
3. LED is always OFF
4. LED is always ON (illuminates dimmer in the dark)
LED bulb adjustments
Not all LED bulbs are made the same, and performance varies between dimmer brands. This can
cause adverse bulb behavior, such as flickering or strobing. T o account for this scenario, this dimmer
features adjustable dim and brightness thresholds to allow setting minimum and maximum levels.
Minimum dim threshold
1. Press OFF button four times, then ON button once quickly.
2. Light starts at the most recent minimum dim level (default — 1%).
3. Press the top or bottom rocker button until the bulb reaches desired brightness without
flickering.
4. The LED stops flashing 10 seconds after releasing the button to indicate the minimum threshold
is set.
NOTE: This can be set by Z-Wave configuration parameter 30/size: 1 byte/values 1-99 (default — 1)
Maximum brightness threshold
1. Press ON button four times, then OFF button once quickly.
2. Light starts at the most recent maximum brightness (default — 99%)
3. Press the top or bottom rocker button until the bulb reaches desired brightness without
flickering.
4. The LED stops flashing 10 seconds after releasing the button to indicate the maximum
threshold is set.
NOTE: This can be set by Z-Wave configuration parameter 31/size: 1byte/values 1-99 (default —99)
Changing paddle color
This step is optional. Before
installation, you may want to change
the color of the paddle to match your
2.
wallplate or décor.
1. Lift the air gap tab at the base of
the paddle.
2. Push side tabs in on one side and
then the other to release paddle.
Lift the cover up and off.
3. Simply put the new paddle onto
the dimmer by inserting the air
1.
gap and side tabs and snapping
securely into place.
Once this step has been completed,
return to section 3.
This device supports Association Command Class (3 Groups)
• Association Group 1 supports Lifeline, Multi-level Switch report
• Association Group 2 supports Basic Set and is controlled with the local load
• Association Group 3 supports Basic Set and is controlled by double pressing the
ON/OFF button
• Each Association Group supports 5 total nodes
NOTE: Actual performance of any CFL or LED will vary from bulb type to bulb type
and among manufacturers. It is important to note only bulbs designed as dimmable
should be used on a dimmer. To find out if your bulb is dimmable, please check the
package, the bulb itself or call the bulb manufacturer directly.
For a complete list of recommended CFL/LED bulbs for this and other Z-Wave
products from Jasco, please visit www.ezzwave.com.
Add-on switch (46199) required
for multi-switch installations.
Connecting the traveler terminal
of this dimmer to a standard
switch will cause damage or
result in improper function. If this
dimmer is a part of a multi-switch
installation, do not connect the
traveler wire or apply power until
add-on switches are correctly
installed. For more information on
3-way or 4-way installations, view
the manual or quick-start guide for
the add-on switch (model 46199).