Zoom X5 Inicio Rápido página 2

Important: Use only the power cube shipped with your X5 modem. Other power cubes may damage the device.
If the POWER LED does not light up, make sure the Switch button is pressed in.
5
Turn on the computer. The ETHERNET LED on your modem's top panel corresponding to the Ethernet port your device is plugged
into should turn on. After a few seconds, your DSL LED will begin blinking, then become solid. If it does not become solid, please
refer to the Troubleshooting Tips in the User Manual on your CD.
S tep 2: Establishing Communication
1
Open your computer's Web browser, enter 192.168.1.1 in the address bar, and press the Enter key.
2
In the Authentication Required dialog box, type the following User Name and Password in lower case, then click OK.
User Name: admin
Password: zoomadsl
3
The Zoom Configuration Manager opens and displays its Basic Setup page.
4
You may choose to use either the Automatic Configuration option or manually enter information provided by your service provider
in the Basic Setup page. We recommend using the Automatic Configuration option. (If you are using a static IP address, you
must manually enter information to establish communication.)
If you choose to manually enter information, please go to the next section (Read This Only if Your Are Manually Entering
Information Into the Basic Setup Page). If you would like to use the Automatic Configuration option, please go to step 5 below.
5
Click on Start under Automatic Configuration. It may take up to 2-3 minutes to detect your connection.
6
If a PPPoE or PPPoA connection is detected, enter the username and password provided by your service provider for PPPoE or
PPPoA protocols. (Your provider should have given you a User ID or User Name, usually your email address or the characters
preceding the @ sign in your email address, and a Password. These are NOT the User ID and Password that you used to get into
the Basic Setup menu.) Click Next three times to reach the Summary Page of the setup.
If a 1483 Bridged IP+NAT or 1483 Routed IP connection is detected, click Next until you reach the Summary Page of the setup.
7
On the Summary Page, click Save/Reboot.
Congratulations! If you want to connect your X5 to only one computer, you are now done. Your modem is connected. To test your
installation, open your browser and go to a familiar Web site. If your browser works, installation is complete for the computer you used
for setup. If your browser doesn't work, please refer to Troubleshooting Tips in the User Manual on your CD.
Read This Only if You Are Connecting Additional Computers and/or Other Devices to the X5 Modem
This section provides general instructions for connecting the X5 to additional computers, game stations, Homeplug adapter pairs,
network devices such as a wireless access point or a switching hub, or a combination of the above. For information about setting up
your specific device, please refer to the documentation that came with that device. Follow the instructions below for each computer or
other device.
1
In setting up the X5, you connected the X5 to a computer. Unplug the computer now if you don't want it to stay connected to the
X5.
2
Plug one end of an Ethernet cable into an available Ethernet port on the X5 and plug the other end of the Ethernet cable into the
Ethernet port of the additional device you want to connect to the X5. (For a hub or a switch, this is typically called an Uplink or
Expansion port. For a router or wireless access point, this is typically called a WAN port.)
3
If you are connecting a computer or game station, go to step 5 below. If you are connecting a Homeplug adapter pair with one
adapter plugged into the X5 and an AC outlet, and the other adapter plugged into a computer or game station and an AC outlet,
make those connections and then go to step 5. If you are connecting a network device such as a wireless access point or
switching hub, go to step 4 below.
4
Set up your network device by using the instructions that came with that device. Then reboot any computer that is part of your
network. For example, if you connected a wireless access point, reboot any computer that will make a wireless connection to that
wireless access point.
5
Verify that your Internet connection is working. Open the Web browser (for example, Internet Explorer or Mozilla Firefox) on each
computer using your network and try to connect to a familiar Web address.
Note: If at any time you need to make changes to the ADSL modem configuration, open a web browser from any PC on your
ADSL modem's network and then type 192.168.1.1 in the address bar to open the modem's Setup pages. Alternately, you can
connect a computer directly to the X5, open its browser, and then type 192.168.1.1. Note also that you can configure the
Management section of the X5 Setup pages to permit configuration from a remote location.
Congratulations! You have connected an additional device to the Internet. You can connect up to 4 devices to the X5, following the
instructions above for each device and starting at Step 2.