Desoutter ELB pistol tools E-LIT PLUS Serie Manual De Instrucciones página 130

6159933730_27
STANDARDS FOR ELC TOOLS
FCC COMPLIANCE (CLASS B)
This device complies with Part 15 of the FCC
Rules. Any changes or modifications not
expressly approved by the manufacturer could
void the user's authority to operate this device.
Operation is subject to the following two
conditions:
(1) this device may not cause harmful
interference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
For indoor use only.
Model Identification
ELC-*-W This device contains:
- FCC ID: PVH0965
- IC: 5325A-0965
ELC-*-Z This device contains:
- FCC ID: S4GEM35XA
- IC: 8735A-EM35XA
FCC Responsible party:
Name: Mark Johnson
Position: General Manager
Address: Chicago Pneumatic Tool Company LLC
1815 Clubhouse Road Rock Hill
SC 29730
USA
Mobile: +1 800 624 4735
Email: mark.johnson@desouttertools.com
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy
and, if not installed and used in accordance with
the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the
equipment and receiver.
● Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
● Consult the dealer or an experienced radio/TV
technician for help.
This portable equipment with its antenna
complies with FCC's radiation exposure limits set
forth for an uncontrolled environment.
This equipment has shown compliance with
FCC's Specific Absorption Rate (SAR) limits.
To maintain compliance, follow the instructions
below:
● This transmitter must not be co-located
or operating in conjunction with any other
antenna or transmitter.
IC COMPLIANCE (CLASS B)
CAN ICES-3(B)/NMB-3(B)
(English)
This device complies with Industry Canada's
licence-exempt RSSs. Operation is subject to the
following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference,
including interference that may cause
undesired operation of the device.
This portable equipment with its antenna
complies with RSS102's radiation exposure limits
set forth for an uncontrolled environment.
This equipment has shown compliance with
RSS102's Specific Absorption Rate (SAR) limits.
To maintain compliance, follow the instructions
below :
● This transmitter must not be co-located
or operating in conjunction with any other
antenna or transmitter.
(French)
Le présent appareil est conforme aux CNR
d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes:
1) l'appareil ne doit pas produire de brouillage;
2) l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le
fonctionnement.
Cet équipement portable avec ses antennes est
conforme aux limites d'expositions de la CNR102
applicables pour un environnement non contrôlé.
Cet équipement a démontré la conformité aux
limites de Débit d'Absorption Spécifique (DAS).
Pour maintenir la conformité suivez les
instructions ci-dessous:
● Cet émetteur ne doit pas être co-localisé
ou opérer en conjonction avec toute autre
antenne ou émetteur.
130 / 134 10/2019