Publicidad
Idiomas disponibles
Idiomas disponibles
GB
The new superheterodyne receiver always guarantees a correct
functioning in disturbed environments: its good sensitivity and high
selectivity make it immune from most disturbances around the
frequency reception area.
The new self-learning programming system enables the memorization of
the ROYAL and ROYAL PLUS series transmitters.
PROGRAMMING
The self-learning programming system enables the code memorization
and the setting of the following functioning modes:
MONOSTABLE: it activates the corresponding relay through the time of
tx transmission. When the transmission stops, the relay goes
automatically off.
BISTABLE: it activates the corresponding relay on the first tx
transmission. The relay goes off on the second transmission.
TIMER: the tx transmission activates the corresponding relay which
goes off after the set time (max 7,5 minutes).
PROGRAMMING OF THE MONOSTABLE FUNCTION
To start programming, please proceed as follows:
•
Set the wished code on the tx dip switches.
•
Press and release the SW1 rx button for a number of times as
shown in the following table, in order to select the channel you
wish to program with monostable function.
SELECTED CHANNEL
CHANNEL 1 MONOSTABLE
CHANNEL 2 MONOSTABLE
CHANNEL 3 MONOSTABLE
CHANNEL 4 MONOSTABLE
Press and keep pressed the transmitter button: if the receiver led goes
off, it means the transmitted code has been correctly memorized.
IMPORTANT: to memorize the code in the correct way it is necessary
to keep a minimum distance of 1,5 metres between the transmitter
and the receiver's antenna.
PROGRAMMING OF THE TIMER FUNCTION
To memorize the TIMER function on the first channel, proceed as
follows:
1
Set any code on the transmitter dip switches.
2
Press and keep pressed the SW1 button of the receiver : the led
L1 (relating to the first channel) lights up for a few seconds.
3
When led L1 goes off, release the SW1 button. Led L1 starts a
sequence of flashings at low speed (1 flash per second).
The number of flashing corresponds to the time which can be set
as shown in the table.
4
Count the number of led L1 flashings corresponding to the time
you wish to set. Press the rx button SW1 during the wished
flashing: the sequence of flashings stops and led L1 remains on.
5
Press and keep pressed the transmitter button within 5 seconds:
if the receiver led L1 goes off, it means the transmitted code has
been correctly memorized.
To programme channels no. 2, 3 and 4, repeat the above mentioned
steps no. 2, 3 and 4, taking into consideration leds L2, L3 or L4 in
accordance with the selected channel.
N°FLASHING TIME SET
N°FLASHING TIME SET
1
01 sec.
12
2
02 sec.
13
3
03 sec.
14
4
04 sec.
15
5
05 sec.
16
6
06 sec.
17
7
07 sec.
18
8
08 sec.
19
9
09 sec.
20
10
10 sec.
21
11
11 sec.
22
LED ON
N°IMPULSES SW1
L1
L2
L3
•
1
•
2
•
3
4
N°FLASHING TIME SET
12 sec.
23
4 min.
13 sec.
24
4,5 min.
14 sec.
25
5 min.
15 sec.
26
5,5 min.
30 sec.
27
6 min.
1 min.
28
6,5 min.
1,5 min.
29
7 min.
2 min.
30
7,5 min.
2,5 min.
31
BISTABLE
3 min.
3,5 min.
PROGRAMMING OF THE BISTABLE FUNCTION
To memorize the bistable function on the first channel, proceed as
follows:
1
Set the wished code on the transmitter dip switches.
2
Press and keep pressed the receiver SW1 button : led L1 (relating
to the first channel) lights up for a few seconds.
3
When led L1 goes off, release SW1 button; led L1 starts flashing
at low speed (1 flash per second). When the 30 flashings of the
timer function are over, led L1 remains on.
4
Press and keep pressed the transmitter button within 5 seconds:
if led L1 goes off it means the transmitted code has been
memorized in the correct way.
To programme channels no. 2, 3 and 4, repeat the above mentioned
steps no. 2, 3 and 4, taking into consideration leds L2, L3 or L4 in
accordance with the selected channel.
WARNING! IF THE RECEIVER IS SUPPLIED BY 24 VAC-VDC, DO NOT
ACTIVE MORE THAN 2 RELAYS SIMULTANEOUSLY
RELAY CONTACT
The four output relay contacts are normally open type; it is possible to
change it as normally closed type. Refering to fig. 1 connect point A
with point B and cut the trace at point C (Fig.1).
L4
IMPORTANT REMARKS
"This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation."
•
"Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment."
99/05/CE DIRECTIVE CONFORMITY
The WALLY1R, WALLY2R, WALLY4R are in conformity with the provisions
of the following EC directive(s) (including all applicable amendments)
and that the standards referenced here below:
EN 60950, EN 301 489-1, EN 301 489-3, EN 300 220-3
Racconigi, 26/05/2003
V2 ELETTRONICA SPA legal representative
A.Livio Costamagna
Publicidad
