Publicidad
Idiomas disponibles
Idiomas disponibles
E N G L I S H
•
The cable wire colours, or a letter, will be
marked at the connection points of most good
quality plugs. Attach the wires to their
respective points in the plug (see below).
Brown is for Live (L) (2) and Blue is for
Neutral (N) (4).
•
Before replacing the top cover of the mains
plug ensure that the cable restraint (3) is
holding the outer sheath of the cable firmly
and that the two leads are correctly fixed at
the terminal screws.
Never use a light socket.
Never connect the live (L) or neutral
(N) wires to the earth pin marked
E or
.
For 115 V units with a power rating exceeding
1500 W, we recommend to fit a plug to BS4343
standard.
Using an extension cable
If an extension cable is required, use an
approved extension cable suitable for the power
input of this tool (see technical data). The
minimum conductor size is 1.5 mm
cable reel, always unwind the cable completely.
Also refer to the table below.
2
Conductor size (mm
) Cable rating (Amperes)
0.75
6
1.00
10
1.50
15
2.50
20
4.00
25
Cable length (m)
7.5
Voltage Amperes
Cable rating (Amperes)
115
0 - 2.0
6
2.1 - 3.4
6
3.5 - 5.0
6
5.1 - 7.0
10
7.1 - 12.0
15
12.1 - 20.0
20
en-4
2
. When using a
15
25
30
45
60
6
6
6
6
10
6
6
6
15
15
6
10
15
20
20
10
15
20
20
25
15
20
25
25
-
20
25
-
-
-
230
0 - 2.0
6
2.1 - 3.4
6
3.5 - 5.0
6
5.1 - 7.0
10
7.1 - 12.0
15
12.1 - 20.0
20
Assembly and adjustment
Prior to assembly and adjustment
always unplug the tool.
Inserting and removing a cutter (fig. B)
•
Press and hold down the spindle lock (2).
•
Using the 17 mm wrench, loosen the collet
nut (3) a few turns and insert a cutter.
•
Tighten the collet nut and release the spindle
lock.
Never tighten the collet nut without
a cutter in the collet.
Replacing the collet assembly (fig. C)
Your router is supplied with a 8 mm (GB: 1/4")
collet fitted to the tool. Two other precision collets
are also available to suit the cutter used. The
collet and the collet nut are inseparable.
•
Loosen the collet nut (3) completely.
•
Remove the collet assembly (21).
•
Fit a new assembly and tighten the collet nut
(3).
Setting the electronic speed control dial
(fig. A)
The speed is infinitely variable from 8,000 to
-1
24,000 min
using the electronic speed control
dial (19) for uniform cutting results in all types of
wood, plastics and in aluminium.
•
Turn the electronic speed control dial to the
required level.
Generally, use the low setting for large diameter
cutters and the high setting for small diameter
cutters. The correct setting, however, is a matter
of experience.
1 = 8,000 min
-1
-1
2 = 9,500 min
-1
3 = 11,500 min
-1
4 = 16,000 min
-1
5 = 19,500 min
6 = 22,500 min
-1
7 = 24,000 min
-1
6
6
6
6
6
6
6
6
6
6
6
6
6
10
15
10
10
10
15
15
15
15
15
20
20
20
20
20
25
--
30
Publicidad
