Residual Risks - BTI BM 701 E Manual Del Usuario

ENGLISH
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power
tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better
control of the power tool in unexpected
situations.
f) Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught
in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk
of starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool's operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier
to control.
g) Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the working
conditions and the work to be performed.
Use of the power tool for operations
20
BTI_BM 701 E_COMBINED.indd Sec1:20
different from those intended could result in
a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional Specifi c Safety Rules
for Drills
• Wear ear protectors. Exposure to noise can
cause hearing loss.
•
Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
• Hold power tool by insulated gripping
surfaces only, when performing an
operation where the cutting accessory
may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire
may make exposed metal parts of the
power tool "live" and shock the operator.
• Use clamps or other practical way to secure
and support the workpiece to a stable
platform. Holding the work by hand or
against your body is unstable and may lead
to loss of control.
• Wear safety goggles or other eye
protection. Drilling operations cause chips
to fly. Flying particles can cause permanent
eye damage.
• Bits and tools get hot during operation.
Wear gloves when touching them.
• Keep handles dry, clean, free from oil and
grease. it is recommended to use rubber
gloves. This will enable better control of
the tool.

Residual Risks

T he following risks are inherent to the use of drills:
– Injuries caused by touching the rotating parts
or hot parts of the tool.
In spite of the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These are:
– Impairment of hearing .
– Risk of squeezing fingers when changing
accessories.
– Health hazards caused by breathing dust
developed when working in wood.
– Risk of personal injury due to flying particles.
– Risk of personal injury due to prolonged use.
25/05/2017 10:01