Juliana Premium Manual De Instrucciones página 4

GB
May we congratulate you on your new greenhouse
Dear Customer!
DEAR CUSTOMER
Congratulations on purchasing your new
The assembly of your new house requires
greenhouse. It is important that you follow these
a bit of technical knowledge. However, it is
assembly instructions step-by-step.
important that the assembly instructions are
followed strict-ly. The assembly instruction
The assembly instructions are a combination of text
is a combination of text and illustrations. The
and illustrations. The profiles are packed in separate,
profiles are packed in separate numbered packs
numbered packs corresponding to their order of use
corresponding to the order in the assembly
in the instructions. Assemble one pack at a time. All
nuts, bolts and fittings are contained in a Box.
instruction. Erect one pack at a time. All nuts
Each pack is specified in separate lists of
and bolts and fittings are found in bag No. 0
components.
(specified on page 12). Each pack is specified in
All detailed illustrations are marked with the
separate lists of components.
following symbols:
All detailed illustrations are marked with
symbols:
Seen from the inside Seen from the outside
Seen from inside Seen from outside.
This part is used on page
Precautions.
• Assembly must only be carried out in dry
SOME SAFETY PRECAUTIONS
and calm weather.
• Assembly must only be carried out in dry and
• Always use working gloves while glazing.
calm weather.
Greenhouse glass has sharp edges,
• Always wear work gloves when installing the
especially if the glass breaks.
glazing. Greenhouse glass has sharp edges,
• Assistants and especially children must be
especially if it breaks.
• warned that broken glass is an element of Assistants and especially children must be
warned that broken glass is dangerous. Pick
danger. Pick up broken glass at once and
up all broken glass at once and remove it with
remove it with care.
care.
• We recommend to use protective glasses
• We recommend that you wear protective
while fixing the spring wire clips.
glasses while fixing the spring wire clips.
• Place the ladder on a level support.
• Any ladders that are used must be placed on a
• It is essential to have an assistant.
level surface.
• It is essential to have an assistant available.
References
TOOLS
The column marked indicates the
Assembling the greenhouse requires tools.
page(s) on which the component is used.
FOUNDATIONS
Page 13:
The base is not included in this consignment, but an
Foundation
original base/wall can be purchased separately. This
The base is not included in this delivery.
base is easy to construct and will guarantee you a
However, an original base can be bought
stable base for your greenhouse.
separately. It ensures you a stable and easy to If you construct your own base, the specified
measurements must be external measurements.
build base.
If you buy our original base/wall, the anchor legs
If you make your own base the measurements
must be cast in cement in eight places. These eight
indicated must be external measurements.
holes must be dug out to below the frost line. Place
If you buy an original base you furthermore
the assembled base with anchor legs over the holes
need about 75 litres of concrete and 6/8
so the anchor legs fit into the holes; it takes about
plastic-/concrete pipes of about 800 mm which
75 litres of concrete to fill up the holes.
are placed in a non-freezing depth for the
Make sure the base is completely level and square.
To square the base, make sure the two diagonal fastening of the corner and middle anchors.
measurements are identical.
The base must be 100% level and square; the
The width of the front and back gables must also be
latter is ensured by checking that the two
identical.
diagonal measurements are equal.
ATTACHMENT TO THE BASE/WALL
Tools
If you build the base yourself, drill holes that fit the
The mounting of the greenhouse requires the
size of the screws you have purchased and choose
tools shown on page 12.
screws that are appropriate for the wall material,
The greenhouse must then be secured to the base
using screws (A).
Page 14-27:
If you are using an original base/wall, attach the
Place the components as shown on the
house using the self-tapping screws included for the
illustration and assemble in the order shown
pre-drilled holes.
in the pictures. Do not tighten the nuts
completely until the front gable construction
has been assembled.
Page 13:
ORDER OF ASSEMBLY
Place the components as shown on the illustration
(Fastening to the base).
and assemble in the order shown in the pictures. Do
When constructing your own base you have
not tighten the nuts fully until the entire sub-frame
to drill holes (7 mm) in the ground frame
has been assembled.
between all the vertical frames, the greenhouse
is then fastened to the base with screws (A).
DOORS AND WINDOWS
Using an original base the greenhouse is
For easier assembly, we recommend that you oil the
fastened to each vertical bar as shown on
screws for the doors. The glass or polycarbonate for
drawing B/C.
the door(s) and windows must be fitted at the same
time as the profiles.
Page 24-27:
FITTING OF GLASS
For an easier assembly we recommend that you
Important before assembly!
oil the screws for the doors.
Make sure that the gables and sides are level
and square and that door(s) and window(s) are
Fitting of glass/polycarbonate
functioning perfectly.
Important before glazing!
The best order of assembly for the glass is as follows:
Windows - Roof - Doors - Gables - Sides
Make sure that gables and sides are level and
square, and that door(s) and window(s) are
GLASS INSTALLATION
functioning perfectly.
Glass installation (illustrations 1 to 8)
Clean the glass and profiles with methylated spirits.
Best order of assembly:
Start glazing from the bottom, one pane at a time.
1) Windows – 2) Roof – 3) Doors – 4) Gables
Apply a 3mm silicone bead around the vertical
– 5) Sides
frames as indicated (the dotted lines on the
illustration). (A 3mm bead of silicone is sufficient to
ensure maximum adhesion). If you use more silicone
Page 30-33:
than recommended, extra tubes can be purchased.
Glazing (illustration 1 to 8)
Degrease the sheets and frames with spirit.
If you accidentally break a pane, carefully pull the
Start glazing from below, one glass at a time.
broken glass outwards and loosen the silicone using
Apply a 3 mm silicone line on the vertical
a sharp craft knife.
frames where indicated (dotted lines on
Clean the profile completely before inserting a new
the illustration). (A 3 mm line of silicone is
pane of glass.
sufficient to obtain maximum attachment). If
you do use more than recommended, you can
buy extra tubes.
Spring wire clips and glassholders are to be
fitted as shown.
X = Spring wire clips, > = Glassholders
In case of broken glass carefully pull it
outwards and loosen the silicone by means of a
sharp craft knife.
Clean the profile completely before inserting a
new pane of glass.
Page 34-37:
Mounting of polycarbonate
The illustrations at the bottom of page 34/36
show where to mount the polycarbonate plates
and lists. The type indication states the length
in mm. A possible adjustment is made by
means of a fine-tooth saw.
NB! To avoid the formation of algae the
polycarbonate sheets must not come into
contact with the ground. Rest them on a piece
of cardboard.
A-lists are mounted as shown on page 35/37.
Put the sheet into the bottom list, bend the
sheet slightly outwards and put it in the top list.
M-lists are mounted as shown on page 35/37.
Place the upper part of the list under the alu.
profile in the whole length of the sheet and
hereafter click on the list from above.
4
Your greenhouse is now fully assembled. However,
Sealing of the polycarbonate sheets
please note the following:
The sheets may be sealed against insects.
Close the top end off with alu-tape or silicone.
MAINTENANCE
The bottom only with airstrip tape to let
• Grease the doors (hinges and locks).
condensation out (available at your local
• Keep the gutters free from leaves, etc.
dealer).
• Adjust the windows as necessary.
• Replace any broken glass.
• Clean the greenhouse with disinfectant before
Now your greenhouse is completely assembled.
and after the growing season.
However, please notice the following:
WINTER PROTECTION
Maintenance
If you anticipate snow during the winter, we
• Grease doors (hinges and lock).
recommend the following winter precautions:
• Clean the gutter for leaves, etc.
• Support the apex of the roof in the middle.
• Adjustment of windows.
• Remove any deep snow from the roof.
• Replacement of broken glass.
• Take precautions to prevent snow falling from
a tree or roof, for example.
• Clean the house with disinfectant before
• Remove the cylinders for the automatic
and after the growing season.
window openers, if fitted (optional extras).
• Secure the door(s) and window(s) to prevent
Winter Protection
wind damage to the greenhouse.
In areas with occurrence of snow we
recommend the following winter protection:
WATER AND CONDENSATION
• Support the roof ridge at the centre of the
Please note that your greenhouse is not like a
house.
conservatory, for example, and that you should
therefore be aware that the greenhouse may leak
• Remove greater snow loads from the roof.
during or after precipitation and that condensation
• Take precautions against snow falling
will occur on the inside of the greenhouse. Good
down from for instance a tree or a roof.
ventilation will help prevent condensation.
• Dismount the cylinders for the automatic
window openers, if any (optional extras).
INSURANCE
• Secure door(s) and window(s) preventing
Please note that not all insurance companies cover
wind damage to the house.
greenhouses automatically. Please contact your
insurance company to ensure that your greenhouse
is covered.
Insurance
Please note that not all insurance companies
GUARANTEE
cover glasshouses automatically. Please
Juliana greenhouses are covered by a 12-year
contact your insurance company to ensure an
guarantee, which covers the replacement or repair
insurance coverage.
of faulty parts. The guarantee does not cover
polycarbonate, glass, transport, assembly, freight,
Guarantee
etc.
Juliana grants a guarantee of 12 years which
Juliana greenhouses are covered by a two-year
warranty on painted parts, where fitted. Note that covers replacement of faulty parts. The
marks on the paint may occur due to suspension of
guarantee does not cover polycarbonate, glass,
the profiles.
transport, assembly, freight etc.
The guarantee will be void if the greenhouse is not
Juliana grants a guarantee of 2 years on painted
assembled in accordance with these instructions.
parts, if any. Note that marks in the painting
may occur due to suspension of the profiles.
COMPLAINTS
The guarantee is invalid if the greenhouse is
All our greenhouses are built to the highest quality
not assembled according to these instructions.
standards. However, should you experience any
problems, please contact your dealer at once. When
describing the defect, please state the greenhouse
Complaints
model, the component number.
All our greenhouses are built to high standards
of quality. However, should a complaint
Congratulations on your new greenhouse, which we
occur please contact your dealer at once.
hope will bring you a lot of pleasure for many years
Remember to specify the defect by indicating
to come.
the greenhouse model and number of the
component and the quality control number.
Yours sincerely,
Juliana Drivhuse A/S
USA