Tiger ontario 5029 Manual De Instrucciones página 2

General
Tiger hand basin taps are designed for installation on hand basins with a tap opening of 30 - 37 mm
(according to NEN-EN 32).The taps are connected to the cold water supply using flexible pressure hoses
suitable for connection using 10 mm bulkhead couplings.
Ontario hand basin tap assembly instructions
Installation:
(see accompanying drawings)
Before you start: Flush the pipes thoroughly in order to make sure there that no dirt can get into
the tap from the pipes. The warranty does not cover damage to interior parts as a result of dirt.
1. Your Ontario hand basin tap features a 'Top fixing' system. This means that installation above the
hand basin requires no special tools. Check whether the assembly unit is put together properly
by comparing it with the drawing. The markings should always be facing outward
during assembly.
2. Push the bottom plate through the hole in the sink by bending the flexible help strips somewhat.
3. Hold onto both help strips and slide the top plate together with the flexible sealing washer.
4. Insert the three assembly bolts (included) and tighten these firmly and evenly.
5. Check whether the assembly plate is mounted straight with the marking on the front. Snip or slice
the help strips off. Any parts of the gasket protruding from the upper assembly plate must be cut off.
6. Push the flexible pressure hose through the opening of the assembly unit and put the tap on the
sink.
7. Attach the tap to the assembly unit by firmly tightening the assembly screw on the back.
8. Connect the feed hoses to your water mains using compression fittings (not supplied). Red (right)
is hot, blue (left) is cold. The pressure hose has a diameter of 10 mm. The connection to the
water mains differs for each house. Compression bushes are available from your dealer (article
number 4550.3.55.41, 2 pieces) to connect to a stopcock with a 3/8 threaded connection.
9. Operation: When the handle points upward, the water supply is closed off. Regulate the volume
in a continuously variable manner by moving the handle forward.
Turn on the water pressure and check for leaks. Tiger disclaims any and all liability for damage caused by
improper use. Your tap is now ready to use.
Features:
Your Hand basin tap features:
• 'Top fixing' assembly system. The tap is installed from the top, without the need for any special tools
• Ceramic discs
• Solid brass housing and handle
• PEX flexible pressure hose (a standard feature for use in drinking water units under the new
international standard)
• Regulated aerator with anti-calcium function, independent of pressure
Maintenance:
Clean with a soft, damp cloth; do not use any abrasives. The warranty does not cover damage caused by
insufficient or improper maintenance, the use of aggressive abrasives, scratches, negligence, normal wear
and tear or changes to the structure made by non-qualified persons. Anti-calcium aerator: Remove the calcium
deposits by rubbing firmly with your fingertips across the outlet (aerator) of the tap. Thanks to its special
design and flexible material, this should be enough to restore the high-performance action of the aerator.
Service and warranty:
Tiger guarantees that your hand basin tap will work perfectly. However, should there be any problem with
your tap resulting from any production and/or material error, Tiger will replace the defective part(s) free
of charge within the 5 year warranty period. If the tap cannot be repaired, you may claim a replacement
product under the warranty. Your proof is purchase is also your warranty, and should be submitted when making
any warranty claims. The drawing on page 11 contains an overview of all of the parts and the corresponding article
numbers.
-2-
5000.5.03.30
5000.5.03.01
(3pcs)
C B
5000.5.07.51 A
5000.5.01.10
(2pcs)
Ø10 Ø10
5000.5.80.51
10.
5000.5.03.98
(1pcs)
service parts
Ø10 3/8
art. nr. 4550.3.55.4
3/8 x 10 (2pcs)
-11-
5000.5.55.96
(R)
5000.5.03.53
5029.5.03.10
5000.5.03.52
FRONT
5000.5.55.05
1. 2.
3. 4.
-12-
5. 6.
7.
-13-