Residual Risks - Stanley FATMAX FMCD900 Manual De Instrucciones

Hold power tool by insulated gripping surfaces when
u
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
Never use a chisel accessory in rotary mode. The
u
accessory will bind in the material and rotate the drill.
Use clamps or another practical way to secure and
u
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
Before drilling into walls, floors or ceilings, check for the
u
location of wiring and pipes.
Avoid touching the tip of a drill bit just after drilling, as it
u
may be hot.
This tool is not intended for use by persons (including
u
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the appliance.
The intended use is described in this instruction manual.
u
The use of any accessory or attachment or performance
of any operation with this tool other than those
recommended in this instruction manual may present a
risk of personal injury and/or damage to property.
Use a face or dust mask whenever the operations may
u
produce dust or flying particles.
Safety of others
This appliance is not intended for use by persons
u
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they do not
u
play with the appliance.

Residual risks

Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving parts.
u
Injuries caused when changing any parts, blades or
u
accessories.
Injuries caused by prolonged use of a tool. When using
u
any tool for prolonged periods ensure you take regular
breaks.
(Original instructions)
Impairment of hearing.
u
Health hazards caused by breathing dust developed when
u
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by
EN 60745 and may be used for comparing one tool with
another. The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the
trigger time.
Labels on tool
The following pictograms are shown on the tool along with the
date code:
Warning! To reduce the risk of injury, the
f
user must read the instruction manual.
Wear ear protectors with rotary hammer drills.
Exposure to noise can cause hearing loss
Additional safety instructions for batteries and
chargers (Not provided with the FMCD900B)
Batteries
Never attempt to open for any reason.
u
Do not expose the battery to water.
u
Do not store in locations where the temperature may
u
exceed 40 °C.
Charge only at ambient temperatures between 10 °C and
u
40 °C.
Charge only using the charger provided with the tool.
u
p
When disposing of batteries, follow the instructions given
u
in the section "Protecting the environment".
Do not attempt to charge damaged batteries.
ENGLISH
5