Publicidad
- fasten rip fence with 2 knobs R
- guide the tool with consistent feed across the
workpiece
• Using the rip fence with curve buffer V ^
- mount curve buffer V (with guide roller mounted) as
illustrated
- guide the tool along the workpiece edge with light
sideward pressure
APPLICATION ADVICE
• Use the appropriate router bits &
• For cuts parallel with the side of your workpiece use rip
fence
• For making parallel cuts in a workpiece far from the
edge !
- fasten a straight piece of wood on the workpiece by
means of 2 clamps
- guide tool with base-plate along edge of wood which
now functions as a rip fence
• When using bits with a pilot or ball bearing, the pilot or
ball bearing should slide along the edge of the
workpiece which should be perfectly smooth *
• For larger routing depths, it is recommended to carry
out several repetitive cuts with lower removal rates
• Vibration level
The vibration emission level stated at the back of this
instruction manual (indicated by an asterisk) has been
measured in accordance with a standardised test given
in EN 60745; it may be used to compare one tool with
another and as a preliminary assessment of exposure to
vibration when using the tool for the applications
mentioned
- using the tool for different applications, or with
different or poorly maintainted accessories, may
signifi cantly increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may
signifi cantly reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
MAINTENANCE / SERVICE
• Always keep tool and cord clean (especially the
ventilation slots P 2)
• Lubricate sliding bars W 2 occasionally
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skileurope.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol ( will remind you of this when the need for
disposing occurs
F
Défonceuse
INTRODUCTION
• L'outil est conçu pour le fraisage des rainures, bords,
profi ls et rainures droites dans le bois, les matières
plastiques et matériaux de construction légers ainsi que
pour le fraisage par copiage
• Lisez et conservez ce manuel d'instructions 3
SPECIFICATIONS TECHNIQUES 1
ELEMENTS DE L'OUTIL 2
A Blocage de l'arbre
B Chapeau
C Clé
D Levier de verrouillage
E Bouton de réglage
F Jauge de profondeur
G Tourelle de butées de profondeur
H Molette pour régler la vitesse
J Adaptateur de l'aspirateur
K Interrupteur de sécurité
L Commutateur
M Guide parallèle
N Semelle
P Fentes de ventilation
SECURITE
INSTRUCTIONS GENERALES DE SECURITE
ATTENTION! Lisez tous les avertissements de
sécurité et toutes les instructions. Ne pas suivre les
avertissements et instructions peut entraîner un choc
électrique, un incendie et/ou de graves blessures sur les
personnes. Conservez tous les avertissements et
toutes les instructions pour pouvoir s'y reporter
ultérieurement. La notion d'"outil électroportatif" dans les
avertissements se rapporte à des outils électriques
raccordés au secteur (avec câble de raccordement).
12
1833
Publicidad
