Publicidad
Idiomas disponibles
Idiomas disponibles
en
30
Handling hazardous dusts
For work procedures with this power tool where
material is removed, dusts develop that can be hazard-
ous to one's health.
Contact with or inhaling some dust types, e. g. asbestos
and asbestos-containing materials, lead-containing coat-
ings, metal, some wood types, minerals, silicate parti-
cles from materials containing stone, paint solvents,
wood preservatives, antifouling paints for vessels, can
trigger allergic reactions to the operator or bystanders
and/or lead to respiratory infections, cancer, birth
defects or other reproductive harm. The risk from
inhaling dusts depends on the exposition. Use dust
extraction matched appropriately for the developing
dust, as well as personal protective equipment and pro-
vide for good ventilation of the workplace. Leave the
processing of asbestos-containing materials to special-
ists.
Wood and light-metal dust, hot mixtures of grinding
dust and chemical materials can self-ignite under unfa-
vourable conditions or cause an explosion. Avoid
sparking in the direction of the dust collector as well as
overheating of the power tool and the materials being
sanded, empty the dust collector/container in time,
observe the material manufacturer's working instruc-
tions, as well as the relevant regulations in your country
for the materials being worked.
Operating Instructions.
Guide the power tool toward the workpiece only
when switched on. Otherwise, the workpiece and
application tools may be damaged.
During machining, the guide roller must always be in
contact with the workpiece.
Firstly remove the switched-on power tool from
the workpiece and then switch it off. Otherwise,
the workpiece and application tools may be damaged.
If power tool vibrations increase significantly,
check the setting parameters for the respective
application material and the condition of the application
tool.
Danger of injury from chippings.
WARNING
Always keep your hands, clothing
etc. away from chippings. Do not attempt to remove
the application tool when still rotating. This can lead to
serious injuries.
Danger of injury from sharp edges
WARNING
of the milling head. Do not touch
the sharp edges of the milling head.
Danger of burning. The application
WARNING
tool can become hot during opera-
tion. Allow the application tool to cool down:
– after placing the power tool down
– prior to tool changing.
Rotate or turn around the eightfold heads as required.
Please note that milling head, guide rollers and indexa-
ble inserts may vary depending on the application. Only
use accessories approved for the application.
When machining bevels and radii, pay attention that the
correct speed stage is set dependent of the material.
Various materials can be subject to hardening at the
edges due to heating, plasma or laser cutting. This can
lead to very high deviations from the specified refer-
ence values.
Setting the bevel height (see page 10/11)
c
a
Use indexable inserts for bevels, which are available as
accessories. Set the bevel height "a" via the setting
dimension at the guide plate. Make a test run. As the
scale has a tolerance of approx. ± 1 mm (approx.
1/32''), readjustment may be necessary. Readjustment
is made using the second scale (numbers 1 to 15) on the
guide plate. The guide plate is adjusted by 0.1 mm
(1/254'') per digit. The maximum, material-dependent
setting dimension and the recommended speed stage
can be found in the following two tables.
Setting the radius dimension (see page 11)
Use indexable inserts for radii, which are available as
accessories. The setting dimension of the guide plate
must be adapted to the respective radius. For setting
dimension values, please refer to the respective acces-
sory. For the material-dependent speed stage, please
refer to the two tables below.
Max. setting dimen-
sion
(applies for 45° bevel
and radius)
[mm]
Aluminium
3.5
Steel
2
400 N/mm
3.5
Steel
2
600 N/mm
2.8
Steel
2
900 N/mm
2.8
Stainless steel 1.4
The specified values are empirical values and can-
not be guaranteed.
Handling the battery.
Store, operate and charge the battery only using FEIN
battery chargers within the battery operating-tempera-
ture range between 5 °C – 45 °C (41 °F – 113 °F). At
the beginning of the charging procedure, the battery
temperature must be within the battery operating-tem-
perature range.
Recom-
mended speed
stage
[inch]
2/16
6
2/16
6
2/16
4–5
2/16
4–5
1/16
1–3
Publicidad
