Stanley FATMAX V20 SFMCSTB933 Manual Del Usuario página 14

English
As you use the trimmer, the string will get shorter due to wear.
Gently bump the trimmer on the ground while running at
normal speed and the line will feed.
nOTE: Extending nylon line beyond the 330 mm swath will
negatively affect performance, runtime, and the life of the
trimmer due to potential of damaging motor. Doing so may void
the warranty.
Helpful Cutting Tips (Fig. M)
• Use the tip of the string to do the cutting; do not force string
head into uncut grass.
• Wire and picket fences cause extra string wear, even
breakage. Stone and brick walls, curbs, and wood may wear
string rapidly.
• Do not allow spool cap
other surfaces.
• In long growth, cut from the top down and do not exceed
305 mm high.
• Keep trimmer tilted toward the area being cut; this is the
best cutting area.
• The trimmer cuts when passing the unit from the left to
right. This will avoid throwing debris at the operator.
• Avoid trees and shrubs. Tree bark, wood moldings, siding,
and fence posts can easily be damaged by the string.
Reloading the Cutting Line (Fig. K–M)

WARNING:
personal injury, turn unit off and remove the battery
pack before making any adjustments or removing/
installing attachments or accessories, when
replacing line, or prior to cleaning. An accidental start-
up can cause injury.

CAUTION:
replacement spools and line. Using any other
manufacturer's line can reduce performance, damage the
trimmer or cause personal injury.
Your trimmer uses 2 mm diameter line that is spiral-
shaped with smooth round edges. Do not use other size
lines. This can degrade performance, cause damage to the
unit or injury.

CAUTION:
cutting line protrudes beyond the trimming blade, cut it off
so that it just reaches the blade.
Use only STANLEY FATMAX replacement line.
1. Remove battery.
2. Cut a max of 6 m length of of 2 mm trimmer line.
3. Align spool housing eyelets
spool grip cover as shown in Figure K.
20
4. Thread one end of the trimmer line through an eyelet. Guide
the line through to the second eyelet and continue to pull
the line through until there are equal lengths of string on
each side of the spool housing as shown in Figure L.
12
to drag on ground or
28
To reduce the risk of serious
Use only STANLEY FATMAX
To avoid appliance damage, if the
with the arrow
21 18
5. Secure the spool cap
your other hand, wind the string onto the spool by rotating
the spool grip cover
winding until 101 mm of string remain on each side of the
spool housing.
MAINTENANCE
Your STANLEY FATMAX power tool has been designed
to operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends upon
proper tool care and regular cleaning.

WARNING:
personal injury, turn tool off and disconnect battery
pack before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING:
main housing with dry air as often as dirt is seen collecting
in and around the air vents. Wear approved eye protection
and approved dust mask when performing this procedure.

WARNING:
chemicals for cleaning the non-metallic parts of the
tool. These chemicals may weaken the materials used in
these parts. Use a cloth dampened only with water and
mild soap. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
Helpful Cleaning Tips (Fig. N)
• Keep the air intake slots
• Your trimmer line can dry out over time.
• Plastic parts may be cleaned by using a mild soap and a
damp rag.
• The line cutter on the edge of the guard can dull over time.
It is recommended you periodically touch-up the sharpness
of the blade with a file.
Replacement Accessories

WARNING:
on the
personal injury, turn appliance off and remove
battery before making any adjustments or
removing/installing attachments or accessories.
from moving with one hand. Using
28
counterclockwise. Continue
20
To reduce the risk of serious
Blow dirt and dust out of the
Never use solvents or other harsh
clean to avoid overheating.
27
To reduce the risk of serious