MTX Audio Ultimate Apple AirPlay Lightning iT1air Manual Del Usuario página 3

Lightning Dock & Compatible Devices
Put one of the following devices in the Lignhtning dock. Press
the tunes stored on your device.
The Aplle devices not listed here are still compatible. But they'll have to use the USB input (see
Wifi Antenna Connector.
Screw the included wifi antenna here for optimal Airplay® performances.
AUX Analog 3,5mm Jack Input.
Use this input with stereo analog signals from a TV, a Blue Ray/DVD/CD player, an MP3 player, a Tablet, a cellular phone, etc.
Do not forget to press "AUX input" to activate the AUX Analog jack input. The LED will turn purple.
Apple® USB Input.
Do not forget to press once or twice to activate the USB input. The LED will turn green.
USB works with iPhone 5, iPhone 4S, iPhone 4, iPhone 3GS, iPhone 3G, iPhone, iPad (3rd and 4th generation), iPad 2, iPad, iPad mini,
iPod touch (1st through 5th generation), iPod classic, and iPod nano (1st through 7th generation).
AC Power Socket.
Connect your iT1air to the power supply. Use the included power cord.
The unit is compatible with 100~120V / 220~240V AC, 50~60Hz. You don't need to move any switch, the selection is automatic.
IR Remote Control.
Before using the remote control, you must install two AAA batteries. Remove the bottom panel with a 2mm HEX key. Follow the (+)
and (-) signs located around the two springs. See "How To : Install the Batteries in the Remote Control" on the next page.
Stand By On/Off
Source Select : AirPlay
Volume Down
Skip Back/Browse Left
OK
Menu/Browse Back
Subwoofer vol. Down
till the LED#2 turns to red. Launch Music and push play. Enjoy
)
Source Select : USB
Source Select : Aux (Jack)
Volume Up
Browse Up
Skip Forward/Browse Right
Browse Down
Play/Pause
Subwoofer vol. Up
IR Remote Control Behavior.
• A single push will power On or power Off the iT1air. When the unit is Off, the two LEDs will be Off.
Power On/Off
When the Unit in On, the two LEDs are on. LEDs colors depend on the input and wifi settings.
Reset
• A single push will enable Airplay Input - The LED#2 will turn to solid Blue.
Source : AirPlay
• Press and hold for 5 seconds will enable the Direct Wi-Fi mode and you'll be able to stream from your computer, from
Direct mode
iTunes or from your Airplay device directly to the unit without any external network. The iT1air will create the network.
Source :
• First push will enable Dock input - The LED#2 will turn to solid Red.
Dock - USB
• Second push will enable USB input - The LED#2 will turn to solid Green.
Source Select :
• Single push will enable the Aux Analogue 3,5mm jack input - The The LED#2 will turn to solid Purple.
Anologue Jack
• Single push will increase the volume one step - The LED#1 will flash red twice.
Volume Up
• Press and hold will increase the volume gradually - The LED#1 will flash red continuously.
• Single push will decrease the volume one step - The LED#1 will flash red twice.
Volume Down
• Press and hold will decrease volume gradually - The LED#1 will flash red continuously.
Browse UP • Airplay, Dock & USB : Single press will navigate to the top -
• Airplay, Dock & USB : OK/validation -
OK
• Airplay, Dock & USB : Single push
Browse Down
• Single push : Skips to the next track on the iDevice or in iTunes - the LED#1 will flash red twice.
Skip Backward
• Press & hold : Fast backward in the current track - the LED#1 will flash red continuously.
Browse Left
• AirPlay, Dock & USB : Browse the iDevice : move to the left - the LED#1 will flash red twice.
• Single push : Skips to the next track in the iDevice or in iTunes - the LED#1 will flash red twice.
Skip Forward
• Press & hold : Fast forward in the current track - the LED#1 will flash red continuously.
Browse Right
• AirPlay, Dock & USB : Browse the iDevice : move to the right - the LED#1 will flash red twice.
Play / Pause
AirPlay, Dock & USB : Play/Pause - The LED#1 will flash red twice.
Browse Back / Menu AirPlay & USB -> Browse back the iDevice. It is the same behavior as Apple's «Menu» - the LED#1 will flash red twice.
Subwoofer
• Single push : increase the subwoofer volume one step - the LED#1 will flash once.
Volume Up
• Press and hold increase the subwoofer volume gradually - the LED#1 will flash fast.
Subwoofer
• Single push : Decrease the subwoofer volume one step - the LED#1 will flash red once.
Volume Down
• Press and hold decrease the subwoofer volume gradually - the LED#1 will flash red fast.
The LED#1 will flash red twice.
The LED#1 will flash red twice.
will navigate to the bottom. The LED#1 will flash red twice.