In accordance with EN 806-5, the following measures must
be taken:
6.1 Inspection
6.1.1 Pressure reducing valve (FK74CS/
FKN74CS only)
1.
Close shut-off valve on outlet
2.
Check outlet pressure using a pressure meter when
there is zero through-flow
• If the pressure is increasing slowly, the valve may
be dirty or defective. In this instance, carry out
servicing and cleaning (See 6.2 Maintenance)
3.
Slowly open shut-off valve on outlet
6.1.2 Filter
•
The filter must be cleaned by reverse rinsing regularly
•
Non-compliance can lead to the filter becoming
blocked This results in a drop in pressure and
decreased water flow
•
The filter meshes are made of stainless steel. A red
coating as a consequence of rust from the pipelines
has no influence on function or the way the filter works
Do not forget the visual check of the ball valve.
Exchange the KF11SB filter bowl in case of drop
formation!
(Connection sizes:
1
1
/
" - 1
/
"
KF11SB-1A
2
4
1
1
/
" - 2"
KF11SB-2A)
2
6.2 Maintenance
6.2.1 Pressure reducing valve (FK74CS/
FKN74CS only)
1.
Close shut-off valve on inlet
2.
Close shut-off valve on outlet
3.
Release pressure on outlet side (e.g. through water
tap)
CAUTION!
There is a spring in the spring bonnet. It may cause
injuries if the spring is derailing.
1
Connection sizes
/
" - 1
2
Slacken tension in compression spring
4.1)Lift adjustment handle
4.2)Turn adjustment handle counter clockwise (-) until
it does not move any more
4.3)Loosen cover cap with a screw driver
4.4)Pull out the adjustment handle
1
Connection sizes 1
/
2
Slacken tension in compression spring
4.5)Loosen slotted screw
Do not remove slotted screw
4.6)Turn adjustment handle counter clockwise (-) until
it does not move any more
Do not turn in too far!
MU0H-1186 GE23 R1019
1
/
"
4
" - 2"
GB
5.
Unscrew spring bonnet
• Use plastic wrench
(Connection sizes:
1
1
/
" - 1
/
" ZR74CS
2
4
1
1
/
" - 2"
2
6.
Remove spring and setting unit
7.
Remove slip ring
8.
Remove valve insert with a pair of pliers
9.
Unscrew filter bowl
(Connection sizes:
1
1
/
" - 1
/
" ZR74CS
2
4
1
1
/
" - 2"
ZR10K-11/2)
2
10.
Pull guide piece with O-ring out downwards
11.
Remove slotted ring
12.
Check that sealing ring, edge of nozzle and slotted
ring are in good condition, and if necessary replace
the entire valve insert
13.
Reassemble in reverse order
Before inserting the cover hood, make sure the
square cut-out (hood) is aligned with the square drive
(spindle).
1
1
(
/
" - 1
/
")
2
4
Press in diaphragm with finger before inserting slip
ring
Screw in spring bonnet
1
30 Nm (
/
" - 1
2
1
75 Nm (1
/
" - 2")
2
Put O-ring on filter bowl
Screw in filter bowl hand-tight (without tools)
14.
Set outlet pressure
6.3 Replacement of the filter insert
1.
Close shut-off valve on inlet
2.
Close shut-off valve on outlet
3.
Release pressure on outlet side (e.g. through water
tap)
4.
Unscrew filter bowl
• Use plastic wrench
ZR74CS
ZR10K-11/2 (1
5.
Remove old filter insert and replace by a new one!
6.
Put O-ring on filter bowl
7.
Screw in filter bowl hand-tight (without tools)
8.
Slowly open shut-off valve on inlet
9.
Slowly open shut-off valve on outlet
7
Disposal
Observe the local requirements regarding correct waste
recycling/disposal!
7
ZR10K-11/2)
1
/
")
4
1
1
(
/
" - 1
/
")
2
4
1
/
" - 2")
2