Steam Ironing; Dry Ironing - Redmond RI-C244-E Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 38
3. Minimum steam output (recommended for steaming delicate fabrics);
4. Steam feature disabled (dry ironing);
5. Self-clean feature.

Steam ironing

Most efficient steam ironing can be achieved in • • or • • • temperature modes.Turn
the steam output control dial into the required position. If the dial is in
steam feature disables (use the mode for dry ironing). Turn steam output control dial
in direction towards
position to increase steam output.
Plug in the iron. Heating indicator on the housing will light up to indicate heating. Once
the soleplate reaches the required temperature heating indicator will go out, indicating
that the iron is ready to use.
NOTE! Constant steam is only generated when the iron is horizontal and set to high
temperature. If steam feature is enabled (steam output control dial is not in
tion) and temperature setting is too low water may drip from soleplate.
Steam Shot
Steam Shot feature is used to eliminate stubborn wrinkles. The feature can be used
during steam ironing when heating indicator on the housing is out. If heating indicator
is lit wait for the soleplate to reach selected temperature before using Steam Shot
feature. Steam output control dial must not be in
Briefly press the Steam Shot button during ironing for extra steam. Allow an interval of
2-3 seconds between the shots. Steam Shot feature can be used for vertical steaming.
NOTE! When iron is set to low temperature (
Steam Shot feature may not be applicable.
Vertical steam
Iron REDMOND RI-C244-E can be used in an upright position to remove wrinkles from
hanging drapes, curtains, tulle, as well as dress clothes without taking them off the
hangers.
1. Turn steam output control dial into
2. Turn temperature control dial into • • • position.
3. Wait until soleplate reaches required temperature (heating indicator goes out).
4. Hold the iron vertically with the soleplate facing the garment. To avoid burning
delicate fabrics hold the iron a few centimeters away from the garment.
5. Move the iron from top to bottom briefly pressing the Steam Shot button. Return
to horizontal position every fifth time you press the button.
position
posi-
position.
position) water may drip from soleplate,
position.
6. If heating indicator lights up stop steaming and wait for the soleplate to reach
the required temperature. Resume steaming after heating indicator goes out.
CAUTION! The iron generates high temperature steam! Do not touch steam to prevent
burning. Never iron clothes on the body!

Dry ironing

You can use the iron for dry ironing even if the water tank is full. However, if using the
feature for a long period of time do not fill the tank with too much water.
1. Turn steam output control dial into
2. Turn the temperature control dial to select the temperature appropriate for your
fabric.
3. After soleplate reaches selected temperature and heating indicator goes out, the
iron is ready to use.
Water spray feature
Use water spray feature to dampen hard-to-iron fabrics, remove stubborn wrinkles, and
to iron difficult areas such as collars, etc.
Press water spray button to dampen the fabric :
• slowly and smoothly for a dense spray
• quickly for a vaporized spray
The feature can be used as often as required from any temperature mode, as long as
there is enough water in the water tank.
Anti-drip feature
Anti-drip feature prevents water from dripping onto fabric and enables to iron even the
most delicate garments. Use low temperature setting (• position) to iron delicate
fabrics.
Anti-Calc system
Iron RI-С244-E is equipped with reliable anti-calc system reducing lime scale build-up
(by removing the calcium ions which form mineral deposits when water is heated).
After each use
Turn the temperature control dial and steam output control dial into
the iron from electrical outlet. Open the water tank cap and gently shake the iron above
the sink to empty the tank. Place the iron into a vertical position.
Wait for the soleplate to cool down thoroughly. Wind the cord around heel of the iron.
Store in a vertical position.
RI-C244-E
position.
position. Unplug
GBR
7

Publicidad

Tabla de contenido
loading

Tabla de contenido