Instructions For Use And Installation; The Lunaris Active Series - My Audio LUNARIS Serie Manual De Instrucciones

- LUNARIS ACTIVE SERIES -
1. INTRODUCTION
Congratulations for choosing the LUNARIS Active series of loudspeaker system! To make the best use of the system,
please read this manual thoroughly before operating the equipment.
2. CONTENTS
3. Instructions for use and installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4. The LUNARIS Active series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5. Installation and connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6. Connection panel (LUN 15A - LUN 12A LUN 10A) . . . . . . . . . . . . . . . . . . . . . 10
7. Connection panel (LUN 15MA - LUN 12MA LUN 10MA - LUN 8MA) . . . . . . . . . . . . . . . . . . . . 11
8. Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

3. INSTRUCTIONS FOR USE AND INSTALLATION

1. PROTECTION AND MAINTENANCE
To avoid jeopardizing correct operation, it is best not to position the enclosures for long periods in exposed places (damp,
high temperature, etc.), in dusty environments or those subject to strong vibrations.
On this subject, it's advisable to always leave the protective grid mounted on the enclosures. In the event of breakdown,
do not open the enclosure, but contact the nearest MY AUDIO Centre.
2. CONNECTIONS
Avoid installing your equipment in the vicinity of radios, televisions, etc., since this could cause noisy disturbance. When
connecting other equipment to your sound system, pay close attention to so-called earth loops, which can cause hum: in
the event of interference, try using the SHIELD switch on the enclosure's control panel.
Before connecting the enclosure to the mains supply, make certain that the current corresponds with that indicated on the
rear of the unit (there is an allowance of ±10%).
Always connect the power cable to the enclosure before switching on the enclosure and always remove it after having
switched off. Remember to always connect or disconnect other equipment with the enclosure off and to always switch on
the mixer first, then the enclosure: in this manner, annoying and often dangerous peaks are avoided.
3. CONNECTOR CABLES (FIG.2)
When connecting the enclosures to the mixer, make certain to always use only screened signal cables made up of two
wires plus a braid/screen: the use of unscreened cables could in fact probably cause annoying hum and noise. Check
periodically that your cables are in good condition, correctly wired and with perfectly efficient contacts: in fact many
problems and drawbacks (false contacts, ground hum, crackles, etc.) are caused by the use of unsuitable or damaged
cables.
4. THE LUNARIS ACTIVE SERIES.....................................Fig. 1
The LUNARIS Active series is a range of active loudspeaker systems hosted in high-density MDF cabinets. The series
includes 10 different models.
■
LUNARIS 15A: it is fitted with a 1" compression driver horn and with a 15" woofer. The built-in power module includes
one 300W RMS AB amplifier for the low section and one 50W RMS AB class amplifier for the high section.
■
LUNARIS 12A: it is fitted with a 1" compression driver horn and with a 12" woofer. The built-in power module includes
one 250W RMS AB amplifier for the low section and one 50W RMS AB class amplifier for the high section.
www.myaudio.it LUNARIS ACTIVE