Important Safety Rules - Amtra biopond HALO 3 LED Manual Del Usuario

HALO 3 LED
IMPORTANT SAFETY RULES: This appliance is a LED lighting system for ornamental ponds and aquariums. The IPX8 protection rating iden-
tifies its use in immersion. Any other type of use is not permitted and consequently it is not covered by the manufacturer's responsibility. "
NOTE: BEFORE STARTING ANY OPERATION OF USE AND MAINTENANCE OF THE DEVICE, PLEASE READ THE MANUALS OF USE AND MAINTE-
NANCE. THE MANUFACTURER CANNOT BE HELD IN ANY CASE RESPONSIBLE OF ACCIDENTS OR DAMAGE RESULTING FROM INAPPROPRIATE
USE OF THE DEVICE, AS WELL AS EVEN PARTIAL FAILURE TO OBSERVE THE SAFETY REGULATIONS AND THE INTERVENTION PROCEDURES
DESCRIBED IN THE MANUALS. ATTENTION: THE DEVICE EQUIPMENT CAN BE PUT INTO OPERATION ONLY AFTER IT HAS BEEN CORRECTLY
INSTALLED AND CONNECTED AND THAT THE USER HAS PREVIOUSLY READ THE MANUAL.
CAUTION: This symbol on the product label and on its packaging indicates that this instruction manual must be
read carefully before the appliance is started up or serviced. be held responsible for any damage caused by this ap-
pliance if you have not read and understood this instruction manual carefully or if you have not followed this.
In order to avoid any type of accident, carefully observe the following warnings (in addition to the most basic safety regulations).
-This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by
children without supervision.
- WARNING: Unplug or switch off all appliances in the aquarium or pond before carrying out maintenance.
If the connection plug of some appliance or the socket are wet, turn off the main switch before disconnecting the power cord of the
appliances present.
- The supply cord cannot be replaced. If the cord is damaged the appliance should be scrapped. - Check the voltage on the de-
vice label and ensure it corresponds to the main power supply. - When the device is plugged to the mains, ensure that the
lowest part of the lead is lower than the socket, to avoid any drops of water that are on the lead flowing into the socket.
If the cable is wet, do not touch the plug with your hands and before disconnecting the device, turn the mains switch off.
- We recommend that this device and other electrical aquarium devices should be connected to power supplies with ground fault circuit
interrrupters lnd 30 mA.
Outdoor use: don't bury the power supply cable, but follow the installation rules provided by the local regulations in force and please
consult a qualified electric installer.
During installing the appliance or maintaining it, please don't lift it using the power cord.
Before putting the appliance into operation, make sure you have installed it correctly.
Never carry out repairs or technical modifications to the appliance and use only original spare parts.
CAUTION: avoid direct exposure to sunlight. Do not use if there is a risk of freezing: in winter it is advisable to remove the appliance or
operate it only if it is protected against freezing.
The appliance must only work in the presence of water and can not run dry. Do not use for drinking water. Do not use for flammable or
explosive, abrasive or corrosive liquindi. Use only for the treatment of pond or aquarium water.
CAUTION: do not connect to the public water supply (public aqueduct).
WARNING: the appliance can be immersed in water up to the maximum depth indicated by the following symbol on the product
m
label. Be sure to respect this warning.
Preliminary checks: Checking for damage - Verify that the various parts of the device does not display physical damages due to bumps,
tears or abrasions. Check in particular:
• That there are no signs or dents, indicative of bumps caused by transport.
• The integrity of the the electrical cables.
Damage Reporting Procedure. If any damage is discovered, stop the connection procedure and report the nature of the damage to the
gb
ISTR_HALO_3_LED.indd 6 04/01/19 16:43