Warranty Conditions - Alumexx Eco 6 Manual De Instrucciones

In the interest of personal safety, only use accessories or

aids that have been recommended by Alumexx.
Do not leave any tools or other equipment at the bottom

of the stepladder or ladder which you might trip over.
Should a stepladder or ladder weigh more than 25 kg,

this should be lifted by two people.
Store the ladder/stepladder in a dry place, out of the full

sun, and far away from work which could potentially
damage the ladder/stepladder (i.e. welding, grinding,
demolition work, etc.).
Assembly and/or repair or replacement parts
EN
Replacement parts supplied by Alumexx must be assembled on
EN
the correct Alumexx product and in the same way as the part
that is replaced. Assembly (attachment) and/or repair is
effectuated at the own risk and expense of the client. Alumexx is
EN
not liable for damage caused by incorrect assembly and/or
repair. Against payment, Alumexx can be called in for the repair
of your product, and/or the assembly of the parts in question.

Warranty conditions

This Alumexx product has been designed, manufactured and
tested with the greatest care. Should this product be used in
accordance with the instructions and its intended use, a
warranty will apply under the following conditions (the warranty
period is indicated on the sticker at the side of our products):
1) Alumexx guarantees the reliability of the product and the
quality of the materials used for the product.
2) We will rectify any defects that are covered by the
warranty by replacing the defective part, or the product
itself, or by supplying a part for replacement.
3) Not covered by the warranty are any defects that occur as
a result of the following:
a) Use of the product contrary to its intended use or
contrary to the instructions for use
b) Normal wear and tear of the product.
c) Assembly or repair by the client or by third parties
(with the exception of fitting the spare parts provided
by Alumexx as indicated above under point 2).
d) Any modified governmental regulations concerning
the nature or quality of the material used in the
product.
4) Any defects that are found upon the delivery of the
product should be reported immediately to Alumexx.
Should notification of these defects not take place
immediately, the warranty will be null and void. To make a
claim under the warranty, Alumexx or your Alumexx
dealer has to be provided with the proof of purchase.
5) Any defects of the product have to be reported to Alumexx
or your Alumexx dealer as soon as possible, but in any
case within 14 days of the defect being found.
6) a) Should a claim be made under the warranty
conditions, Alumexx has to have the opportunity to
be able to investigate the product in its Quality
Centre. The client must make the product available
for this purpose. Should it be established during
the investigation that the product has been used
incorrectly, the costs of the investigation will be
charged to the client.
b) Should the client ask for an investigation to be
carried out by an independent institute, the costs for
this investigation are at the expense of the client
should it be established during the investigation that
the product has been used incorrectly. The costs of
18
YOUR NEXT LEVEL SUPPORT!
the investigation are also at the expense of the client
if, prior to this investigation, Alumexx offered to
repair or to replace the product at no charge to the
client.
Checklist inspection and checks before use
Ladders
Check that the stiles (uprights) are not bent, bowed,

twisted, dented, cracked, corroded or rotten.
Check that the stiles around the fixing points and other

components are in good condition.
Check that fixings (usually rivets, screws or bolts) are not

missing, loose, or corroded.
Check that rungs are not missing, loose, excessively worn,

corroded or damaged.
Check that the rung hooks are not missing, damaged,

loose or corroded and engage properly on the rungs.
Check that guide brackets are not missing, damaged, loose

or corroded and engage properly on the mating stile.
Check that rubber feet / end caps are not missing, loose,

excessively worn, corroded or damaged.
Check that the entire ladder is free from contaminants (e.g.

dirt, mud, paint, oil or grease).
Check that locking catches (if fitted) are not damaged or

corroded and function correctly.
Note: If any of the above Checks cannot be fully satisfied you
should NOT use the ladder.
Stepladders
Check that the front stiles and rear legs are not bent,

bowed, twisted, dented, cracked, corroded or rotten.
Check that the stiles / legs around the fixing points and

other components are in good condition.
Check that fixings (usually rivets, screws or bolts) are not

missing, loose, or corroded.
Check that treads are not missing, loose, excessively worn,

corroded or damaged.
Check that the hinges between front and rear sections are

not damaged, loose or corroded.
Check that the locking stays, horizontal back rails and

corner braces are not missing, bent, loose, corroded or
damaged.
Check that rubber feet are not missing, loose, excessively

worn, corroded or damaged.
Check that the entire stepladder is free from contaminants

(e.g. dirt, mud, paint, oil or grease).
Check that the platform (if fitted) has no missing parts or

fixings and is not damaged or corroded.
Note: If any of the above Checks cannot be fully satisfied you
should NOT use the stepladder.
16
EN