Recharging The Battery - VALERA SYSTEMA 654.01 Traducción De Las Instrucciones Originales

RECHARGING THE BATTERY

• Before using the appliance for the first time, charge the battery for 24 hours. For subsequent charges, allow
the appliance to charge for at least 12 hours.
• Switch the appliance off using the switch (fig.1 - ref.3). The battery can only be charged with the appliance
switched off.
• Connect the transformer (fig.1 - ref.9) by inserting the plug into the appliance socket (fig.1 - ref.5). Or
connect the transformer to the base (fig.1 - ref.6) by inserting the plug into the base plug (fig.1 - ref.5), and
rest the appliance on the contact (fig. 1 - ref.7).
• Plug the transformer into the mains.
• The charge light (fig.1 - ref. 4) turns red while the appliance is charging and reverts to green when charging
is complete.
• When the battery is fully charged, the appliance can be used for approximately 50 minutes without connection
to the mains.
• In order to optimise the lifetime of the battery, never charge the appliance for more than 24 hours.
• Discharge the battery completely every few months, then recharge it again. This optimises the lifetime of the
battery.
ADJUSTABLE GUIDE COMBS
The appliance is supplied with two hair/beard and moustache trimming combs, which can be adjusted to offer
different cutting lengths: from 2 to 8 mm and from 10 to 16 mm.
To adjust the guide comb, press the adjustment button (fig.1 ref.16) and slide the comb in or out until it reaches
the desired cutting length, as illustrated in fig. 2.
The various positions can be seen on the comb setting indicator (fig.1 ref.17).
The comb attachment can be removed by lifting the tab at the rear (fig.3); in this case the cutting length is 1
mm.
To refit the comb attachment, slot the front in first (fig.4 - A), then press down on the rear (B).
The appliance is also supplied with an adjustable comb for body hair, with three different cutting lengths: 2, 5
or 9 mm. For cutting length adjustment guidelines, see fig.5.
FITTING AND REMOVING THE HEAD
Please refer to fig.6 when removing the head. For instructions on re-fitting the appliance head, see fig.7.
USING THE HEADS
The appliance is supplied with 5 heads.
• Hair cutting head (fig.1 ref.2) - For trimming hair, can either be used alone or in conjunction with the relevant
combs (fig.1 ref.15).
• Body hair head (fig.1 ref.10) - For trimming body hair, can either be used alone or in conjunction with the
relevant comb (fig.1 ref.14).
• Nose and ear hair head (fig.1 ref.11) - For removing unwanted hair from these areas.
• Beard and moustache head (fig.1 ref.12) - For tidying beards, can either be used on its own or in conjunction
with the relevant combs (fig.1 ref.15).
• Shaver head (fig.1 ref.13) - With fine stainless steel foil for supreme hygiene and narrow design for easier
shaving.
STYLING TIPS
SHORT STYLES
• We recommend starting with the longest cutting length and subsequently adjusting to a shorter length, if
desired.
• Cut hair while dry, using short strokes and progressing slowly.
• Comb the hair as you proceed in order to remove cut hair and check the results.
• NECK: Starting from the midpoint of the bottom of the neck work upwards using short strokes towards the
middle of the head (fig. 8), gradually working outwards to the sides.
• SIDES: We recommend using a shorter cutting length, using the same method as for the neck area.
To finish sideburns and the area around the ears, use the appliance without a guide comb, holding it turned
downwards.
• TOP: Use a longer cutting length. Start at the front and move backwards, towards the centre of the head.
LONGER STYLES
• Use the same method, starting from the neck and working upwards, followed by the sides and then the top
of the head.
• To adjust the cutting length, use the barber's comb (fig.9), or else your fingers to help (fig.10), using the
appliance without a guide comb.
BEARD AND MOUSTACHE TRIMMING
• Decide on the kind of look you want to obtain, based on your face and the length of beard and moustache.
• When trimming beard and moustache, start off with the comb attachment adjusted to a high setting, and then
move onto a shorter setting if so desired. A weekly trim will suffice to maintain the look.
• Define edges using the beard and moustache head (fig.1 ref.12), then use the shaver head (fig.1 ref.13) to
finish.
• For best results, beard and moustache can be dampened (not wet), and brushed in the direction of growth.
• Proceed to trim, working upwards from the bottom, beginning at the jaw and moving towards the ears.
8