Moser ARCO 1854 Manual Del Usuario página 12

ENGLISH
Operation
de
Preparation
Keep the packaging material for safe storage or
transport later.
en
f Check that the contents are complete.
f Check all the parts for possible transport damage.
fr
Safety
it
Handle with care! The incorrect power supply will
cause damage.
f Only operate the appliance with an alternating cur-
es
rent and with the voltage stated on the nameplate.
Charging the battery
pt
This cordless hair clipper is supplied with two battery packs.
While the appliance is in use, the second battery pack can be
recharged on the charging stand. This means that the clipper is
nl
always ready for use.
Before the appliance is used for the first time,
sv
each battery pack should be charged for approx.
90 minutes.
no
1. Connect the appliance plug (R) on the plug-in transformer to
the charging stand socket (H) (Fig. 2ⓐ).
2. Connect the plug-in transformer to the mains socket
fi
(Fig. 2ⓑ).
3. Insert the battery pack into the recess of the charging stand
(Fig. 4). The charging process starts.
tr
· During charging, the red charging indicator (I) is
illuminated.
pl
· It should take around 75 minutes for the appli-
ance to charge to full capacity.
· The second battery can remain in the charging
cs
stand so that a charged battery pack is always
available.
sk
4. Once charging is complete, the charging indicator (I) on the
charging stand (G) will start flashing.
hu
Battery operation
1. Switch on the appliance using the on/off switch and switch
sl
off after use (Fig. 5ⓐ/ⓑ).
· When you press the on/off switch, the battery
ro
power indicator (E) will light up briefly to indicate
that the appliance is ready for use.
· When used as a hair clipper, the appliance can be
bg operated for up to 100 minutes when the battery
is fully charged.
· When used as an animal hair clipper, the appli-
ru ance can be operated for up to 80 minutes when
the battery is fully charged.
· Insufficient maintenance of the blade set can sig-
uk
nificantly reduce the operating life.
· If the battery power indicator (E) on the hand-held
appliance lights up during operation, this means
there is only approx. 15% battery power remain-
el
ing. The battery pack needs to be recharged. You
can now use the charged replacement battery
pack.
ar
12
To recharge the battery:
1. Switch off the appliance using the on/off switch (Fig. 5ⓑ).
2. Press the unlock buttons on the side and remove the bat-
tery pack (Fig. 3ⓐ).
3. Remove the charged battery pack (Fig. 4) and push it into
the appliance until you hear it snap into place (Fig. 3ⓑ).
4. Fit the flat battery pack to the charging stand (Fig. 4). See
Charging the battery.
Operation
Setting the cutting length
The cutting length can be adjusted to between 0.7mm and 3mm
(5 possible positions) using the cutting-length adjustment inte-
grated into the blade set (Fig. 6).
Cutting with attachment combs
The appliance can also be operated with attachment combs.
f In order to achieve the indicated cutting length, the cutting
length adjustment lever should be set to position 1 (Fig. 6).
Depending on the model, the following attachment
combs are included as standard:
3 mm, 6 mm, 9 mm and 12 mm, 18 mm and 25 mm
cutting lengths.
Attaching/removing the attachment comb
1. Slide the attachment comb on to the blade set in the direc-
tion of the arrow until it reaches the limit stop (Fig. 7ⓐ).
2. The attachment comb can be removed by pushing it in the
direction of the arrow (Fig. 7ⓑ).
Maintenance
Cleaning and care
Danger! Penetration of liquid can cause electric
shock.
f Switch off the appliance before any cleaning or
maintenance.
f Do not immerse the appliance in water!
f Do not allow any liquid to get inside the appliance.
f Only reconnect the appliance to the power supply
if it is completely dry.
Handle with care! Aggressive chemicals cause
damage.
Aggressive chemicals could damage the appliance
and accessories.
f Never use solvents or scouring agents.
f Only use the cleaning agents and blade set oil
recommended by the manufacturer.
Hygienic spray and blade set oil are available from
your dealer or our service centre.
f Remove the attachment comb (Fig. 7ⓑ) and lift the blade
set out of the housing (Fig. 8ⓐ). Use the cleaning brush to
remove any cut hairs from the housing opening and from
the blade set (Fig. 9). The cleaning lever (B) can also be
pressed. This allows the cut hairs that accumulate between
the bottom blade and the top blade to be easily removed
using the cleaning brush (EASY CLEANING).
f Wipe the appliance with a soft, slightly damp cloth only.