Publicidad
Safety precautions
Store your tools
in a safe place.
After use, set the tool down on its
standing surface and let it cool be-
fore putting it away.
When not in use, tools must be
stored in a dry, locked room out of
children's reach.
This tool may be used by children
aged 8 or above and by persons
with reduced physical, sensory or
mental capabilities or lack of expe-
rience and knowledge if they are
supervised or have been given in-
structions on how to use the tool
safely and understand the hazards
involved.
Do not allow children to play with the
tool.
Children are not allowed to clean or
carry out maintenance work on the
tool without supervision.
Do not overload your tools.
Your work results and safety
will be enhanced if you operate
the tool within the specified output
range. Do not carry the tool by the
power cord. Do not unplug the tool
by pulling on the power cord. Pro-
tect the power cord from heat, oil
and sharp edges.
Proper use
The STEINEL HL Stick power tool is intended for shaping
plastic as well as for heating shrink tubing. It is also suitable
for soldering, de-soldering and undoing bonded joints.
Beware of toxic gases and
fire hazards.
Toxic gases may develop when
working on plastics, paints, varnish-
es or similar materials.
Beware of fire and ignition hazards.
For your own safety, only use ac-
cessories and attachments that are
specified in the operating instruc-
tions or recommended or specified
by the tool manufacturer.
Using attachments or accessories
other than those recommended in
the operating instructions or cata-
logue may result in personal
injury.
Repairs must only be carried
out by a qualified electrician.
This electric power tool complies
with the relevant safety regulations.
Repairs should only be performed by
a qualified electrician. Otherwise the
user may run the risk of accidents.
If this tool's main power cord is dam-
aged, it must be replaced by the
manufacturer or its customer service
department or a similarly qualified
person so as to avoid hazards.
Keep these safety precautions
with the tool.
The tool is not intended for use as a hot-air barbecue lighter,
as a hair-drier or for use in vehicles.
- 8 -
Technical specifications
Voltage supply
230-240 V, 50 Hz
Output
350 W
Temperatures *
1
400 °C without nozzle
500 °C with 7 mm reduction nozzle (included)
Airflow rate
100 l / min. max.
Mains power cord
H05
Protection class
II
Emission sound pressure level
≤ 70 dB(A)
Total vibration value
≤ 2.5 m/s
2
I K = 0.08 m/s
Weight
0.7 kg
*
1
Temperature profile
Distance from outlet nozzle
20 mm
30 mm
Temperature without nozzle
360 °C
320 °C
Temperature with nozzle
450 °C
350 °C
Tool features
1
Stainless steel outlet nozzle
2
Air inlet
3
ON/OFF slide switch
4
Hanging ring
For your safety
Tool description - Operation
Operation
3
The tool is switched ON and OFF at the
slide switch.
The distance from the object you are working on depends
on material and intended method of working. Always try out
temperature on a test piece first. Using the attachable noz-
zles (see accessories page on the cover) the flow of hot air
can be controlled with maximum precision.
2
40 mm
50 mm
100 mm
150 mm
280 °C
230 °C
150 °C
100 °C
290 °C
250 °C
150 °C
100 °C
5
Rubber sheathed cord
6
LED light for illuminating the work area
7
Standing surface
• The thermal cut-out shuts the tool down if it is overloaded.
• Attaching the reflector nozzle
C D
Take care when changing hot nozzles! When using the
hot air tool in the self-resting position, make sure it is stand-
ing on a stable, non-slip and clean surface.
- 9 -
200 mm
75 °C
75 °C
Publicidad
