Cleaning Instructions - Palram Feria Instrucciones De Montaje

EN
IMPORTANT
Please read these instructions carefully before you start to assemble this patio cover.
Please carry out the steps in the order set out in these instructions.
Keep these instructions in a safe place for future reference.
» Care and Safety advice
•
Please follow the instructions as listed in this manual.
•
Sort the parts and check the list of contents.
•
For safety purposes we strongly recommend that the product will be assembled
by at least two people.
•
Some parts have metal edges. Please be careful when handling components.
Always wear gloves, shoes and safety goggles during assembly.
•
Do not attempt to assemble the product in windy or wet conditions.
•
Dispose of all plastic bags safely – keep them out of reach of small children.
•
Keep children away from the assembly area.
•
Do not attempt to assemble the product if you are tired, have taken drugs,
medications or alcohol, or if you are prone to dizzy spells.
•
When using a stepladder or power tools, ensure that you follow the manufacturer's
safety advice.
•
Do not climb or stand on the roof.
•
Heavy articles should not be leaned against the poles.
•
Do not hang or lay on the profiles.
•
Please consult your local authorities if any permits are required to construct the
product.
•
Keep roof and gutter clean of snow, dirt & leaves.
•
Heavy amounts of snow on roof can damage the product making it unsafe to stand
below or nearby.
•
This product was designed and produced to be a patio cover only.
Some versions of this product are painted.
If color was scratched during assembly it can be fixed with the following tints:
White – RAL 9016
Gray – RAL 7012
» Cleaning instructions
When your product needs cleaning, use a mild detergent solution and rinse with cold
clean water.
Do not use acetone, abrasive cleaners, or others special detergents to clean the panel.
» Before starting assembly
•
This product must be assembled on a solid base (such as concrete).
•
Choose your site carefully before beginning assembly.
Site surface (mainly below poles) needs to be level.
•
During assembly use a soft platform below the parts to avoid scratches and
damages.
» Product dimensions adjusting
Product dimensions can be adjusted to your specific needs.
1. The wall-mounting profile (top-back) can be adjusted
from 285 to 305 cm (112.2" to 120") above ground.
The adjusting is done when measuring and drilling
(step 9).
lease be advised that installation recommendations' height
is suggested in the drawing above. However, it is possible
to fix the Feria patio cover back wall height at a lower point
of 260 cm / 102.4". This method is optional if the assembly
conditions and exterior walls do not allow to follow the
suggested installation as appear
in manual. Please note that the
product appearance may slightly
change as a result, however snow
load weight does not change.
2. Poles distance from the wall
can be adjusted from 226 to
286 cm (89" to 112.5").
The adjusting is done after
assembly and before anchoring
(step 26) by sliding poles and
profile 7030 +7031 at channels of
roof profiles.
3. Poles distance from the side
edges can be adjusted from
0 to 54 cm (0" to 21.3").
The adjusting is done after
assembly and before anchoring
(step 26) by sliding poles and
connectors 937 at channel of
profile 7030 +7031.
Note: Wall mounting and
distance from the wall determine
the roof angle and the total
depth of the product (distance of
gutter from the wall). Higher wall
mounting and shorter distance
between wall and poles increase
the roof angle and shorten the
total depth.Tighten all screws
when completing assembly
226-286cm
89" - 112.5"
0-54cm
0-54cm
0-54cm 0-54cm
0"-21 "
0"-21 "
¼ ¼
0"-21.3" 0"-21.3"
13 º
17
º
285-305cm
102.3"-120"