DeWalt DCR027 Traducido De Las Instrucciones Originales página 29

• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: Use only D
e
Inserting and Removing the Battery Pack
from the Charger/Radio (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Unit
1. Align the battery pack 19
radio's battery port (Fig. B).
2. Slide it in until the battery pack is firmly seated and ensure
that you hear the lock snap into place.
To Remove the Battery Pack from the Unit
1. Press the release button 20
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button 21 . A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
To Install Coin Cell Battery (Fig. B)

WARNING: Danger of explosion if battery is incorrectly
replaced. When replacing battery, replace it with the
same or equivalent type CR2032. Observe correct polarity
(+ and –) when replacing batteries. Do not store or carry
batteries so that metal objects can contact exposed
battery terminals.
1. On the battery door on the back of the unit, turn the
screw 22 anti-clockwise to remove. Screw will remain
captive in the door.
2. Press down on the battery door latch and pull to open.
3. Install the coin cell battery
inside the coin cell battery area.
WALT battery packs and chargers.
19 is fully charged.
with the rails inside the charger/
and firmly pull the battery pack
23 according to the diagram
4. Replace the battery door, insert the screw and tighten.
nOTE: To reset the LCD display, clock, and pre-sets remove
the coin cell battery and re-install. Follow this procedure if the
screen seems to lock in place.

DANGER: DO NOT INGEST BATTERY; CHEMICAL
BURN HAZARD. This product contains a coin/button cell
battery. If the coin/button cell battery is swallowed, it can
cause severe internal burns in just 2 hours and can lead
to death.
Keep new and used batteries away from children. If the
battery compartment does not close securely stop using
the product and keep it away from children.
If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medical attention.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.
Your Bluetooth® charger/radio is equipped with memory
capacity in order to store the time and your selected memory
channels. When the radio is in the OFF position, this memory
capacity is powered by one coin cell battery that is included
with the charger/radio.
Power/Volume Adjustment
1. To turn the radio on, press the power button
nOTE: When the radio is first used it will enter 'DAB' mode
and automatically scan for stations. It will then set the time
and start playing the first station it finds. If there is no time
signal available please refer to To Program the Clock to
manually set the time.
2. Turn the dial 2 clockwise to increase the volume. To
decrease the volume, turn anti-clockwise.
Mode Function
To choose one of the mode functions ('DAB', 'FM', or 'AUX' or
Bluetooth®) push the mode button
is found.
nOTE: Pressing the Bluetooth® button
into Bluetooth® mode.
DAB Mode
Tuning
When the unit is first switched on the unit will start in
'DAB'/'DAB+' mode and will 'Auto Scan' to find broadcast
stations in the local area. Once 'Auto Scan' is complete, use the
left or right arrow buttons to scroll through the stations.
5
nOTE: When moving locations or if reception was poor
in the original scan (possible if the antenna was not up),
this may result in an empty or incomplete list of available
stations. Manually running an 'Auto Scan' will find all available
broadcast stations.
To Perform an auto scan:
1. Press the menu button
10
pressing the right arrow button
EngLIsh
1 .
until the desired function
6
13 also puts the radio
, scroll through the options by
5 until you reach 'Auto
27