Siemens IAR6-30 Guia Del Usuario

Building Technologies
Fire Safety & Security Products
IAR6-30
Contactless ID Access Card Reader 125kHz + Keypad
Berührungsloser ID Zutritts Kartenleser 125kHz mit
Tastatur
Lecteur de badge 125kHz + Clavier
Teclado & lector de tarjetas de proximidad de 125 KHz
Lettore badge di prossimità 125kHz + Tastiera
Leitor de controlo de acessos 125kHz + Teclado
Berøringsfri ID-kortleser 125kHz + Tastatur
Contactloos ID Toegangskaartlezer 125kHz + Keypad
Bezkontaktní čtečka karet 125kHz + klávesnice
Bezkontaktowy czytnik kart dostępu 125kHz z
klawiaturą
125Khz Toegangscontrole kaartlezer/codeklavier
125kHz ID Kartlı Geçiş Okuyucu + Tuştakımı
STEP: A6V10060232
English
Before starting to install and work with this device, please read the Safety
Instructions.
Scope of delivery
IAR6-30 contact less ID access card reader
Covers for the screws
Mounting screws
Plugs
Description
The IAR6-30 is an access card reader which can also arm and disarm the alarm
system.
Installation and wiring instructions
Connect the wires to the IC60 control panel and to any optional device
(refer to the wiring diagram at Fig. 2 and the following colour legend):
Cabel colour Fig. 2
Red a
Black b
Yellow c
Orange d
White e
Green f
Brown g
Blue h
Communication:
Connect the communication wires to the BUS wires coming from the
IC60 control panel (a, b, e, f).
Door Status:
Connect the optional door status wires (b and d) to the door status
switch.
Door Lock Activation:
Connect the optional door lock activation wires (g and h) to the electric
door lock.
Auxiliary Door Lock Power Supply (not provided):
Connect an auxiliary 12 V DC power supply for the door's lock activation.
Install the unit on a flat wall with the 2 screws (Fig. 3).
Cover the screws with the top and bottom covers (Fig. 4).
P/N 7102602 Rev. A
1
3
Address assigning to the IAR6-30
A maximum of 7 devices can be connected to the bus (IKP6, IAR6-30...).
After a IAR6-30 has been connected to the bus, it has to get an address:
Select the "installer mode" in the control panel as described in the installer
manual.
Enter the code P99E followed by the address you wish to assign
(e.g. P99E4E will assign keypad address 4).
To address the reader you need to present a badge 5 times within 10
seconds to the IAR6-30.
When the address is learnt, the control panel stops the learn mode
automatically.
Repeat the same steps for every reader address you want to assign.
When the control panel is in "installer mode", the IAR6-30 LED flashes out
the set address (number of flashes).
Badge / card learning
Up to 100 tags can be used in a system.
A badge has first to be enrolled into the system before starting to work with it.
All badges are assigned to users. Therefore the badge storage options have to be
similar to the user ones (for example if user 11 is assigned to area A, then badge
number 11 will be assigned to area A as well).
Select the "program mode" in the control panel as described in the installer
manual.
Enter P21E and the badge number you wish to enrol, i.e. 11E for tag/card
number 11:
the keypad will start to beep to indicate that learn mode has been started.
Present the badge to the IAR6-30:
once the badge has been received by the control panel and stored, the
IAR6-30 will stop beeping to indicate learn mode is completed.
After learning process, in order to enable the tag operation, you MUST select
the appropriate option at location P2E (options 2, 3 or 4 must be selected for
the badge to work) on the control panel.
2
4
Technical Data
Operation voltage
Current consumption
RF transmission to key
Detection distance
Max number of badges
Dimensions
Door activation drive
Environmental conditions:
Operation temperature
Storage temperature
Humidity (EN60721)
Housing protection EN60529,
EN50102
Complies with: EN50130-4+A1+A2, EN301489-3, EN60950-1, EN61000-6-3,
EN300320-2
For more detailed instructions please refer to the manuals which can be
downloaded from the internet: www.siemens.com/homesecurity
Installation Instruction
11 V DC to 16 V DC
40 mA
125 kHz
Typical: 5 cm
100 per control panel
45x121x21mm
12 V DC max. – 1 Amp.
-10 - +50 °C
-20 - +60 °C
< 85% r.h., non condensing
IP54 / IK02