Oregon Scientific RM511 Guia De Inicio Rapido página 12

ALARM
SETTING/ADJUSTING ALARM TIME
1. Press and hold button, enter alarm setting
2. Sequence of setting: weekday hour
minute exit
3. During setting, the setting parameter will flash.
4. Press button to confirm setting and enter to next parameter
5. Press button once, the figure will increase 1 unit. Press and hold the
will increase rapidly.
6. Press button once, the figure will decrease 1 unit. Press and hold the
figures will decrease rapidly.
7. Press button to turn on/off alarm
8. Alarm will automatic turn on when alarm setting finish.
9. If there is no action in 20 seconds, the setting will be saved and will exit the setting mode.
TURN ON/OFF ALARM
1. When it is displaying the nearest coming Alarm time, press
alarm. (1-5) or (6-7) will flash to indicate which alarm displaying.
2. Press button once to switch to alarm mode. Monday to Friday alarm time will be shown and
(1-5) will flash.
3. Press button once to turn on/off Monday to Friday alarm
4. Press button again to show Saturday to Sunday alarm time. (6-7) will flash.
5. Press button once to turn on/off Saturday to Sunday alarm.
OPERATION
1. At the set time, alarm signal rings.
2. During alarm rings, press any keys to end the alarm. Or press
8 minutes.
3. If do not press any button to end the alarm, it will turn off automatically after 5 minutes.
4. Alarm will be start again at next alarm time, unless switch off the alarm function in alarm mode.
PRECAUTIONS
Hazards for children
Batteries can be life-endangering if swallowed. Please keep the RCC Clock and batteries
out of reach of children. If a battery has been swallowed, please seek medical assistance
immediately.
Keep children away from packaging material and the small parts in the scope of delivery.
Suffocation hazard if swallowed.
Injury hazard
Caution: Explosion hazard with improper handling of batteries. Batteries must not be charged,
reactivated with other means, dismantled, thrown into fire or short-circuited.
Avoid contact with skin, eyes and mucous membranes. When coming into contact with battery
acid, immediately rinse the affected areas with plenty of clear water and immediately contact a
physician.
Caution – property damage
Protect the RCC Clock from dust, impact, extreme temperatures and direct sunshine. Also
protect the RCC Clock from moisture. Exclusively position Projection Clock in a dry,
enclosed space.
Remove the batteries from the RCC Clock, if they become depleted or if you are not using
the RCC Clock for a longer period of time.
weekday minute weekend hour weekend
button, the figures
button, the
button once to turn on/off that
button to delay the alarm for
Do not expose the batteries to any extreme conditions by e.g. placing them on a radiator or
under direct sunlight.
Clean the battery and appliance contacts prior to insertion, if required.
Using same type of batteries. Do not use different types or used and new batteries together.
Do not carry out any changes to the device. Only allow repairs to be carried out by a
professional workshop.
Never use hard, scratching or abrasive detergents or similar, for cleaning the RCC Clock.
This could scratch the surfaces.
SPECIFICATIONS
L x W x H 72 x 25 x 75 mm
Weight (Main unit) 73g (Exclude batteries)
Temperature display range 14℉ to 122℉(-10℃ to +50℃)
Accuracy 0℃ to +40℃: +/- 1.5℃ (+/-3℉)
<0℃ and >+40℃: +/- 2℃ (+/-4℉)
Resolution 0.1℃ (0.2℉)
Power 2 x R03 (AAA) 1.5V batteries
NOTE:
When the temperature is lower than 14℉ (-10℃), the temperature displays LL.L. When the
temperature is higher than 122℉ (50℃), the temperature displays HH.H.
During alarm rings or RCC receiving process, temperature detection will be stopped.
NOTE: The technical specifications for this product and the contents of the user manual are subject
to change without notice.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received, including interference that
may cause undesired operation.