Polisport Wallaby Evolution Manual Del Usuario página 3

WALLABY EVOLUTION
Thank you for purchasing a Polisport product
So that your outdoor excursions become moments of pleasure and happiness, we have
created the Wallaby Baby Seat having in mind your child's safety and comfort
A reclining system was developed for the Wallaby Baby Seat, which allows for the regula-
tion of the back in three positions in order to give your child better comfort when going
out with you.
The Wallaby Baby Seat is adjustable to mountain bicycles, Trekking and City Bikes. For this
purpose we developed a system of regulation of the forward and backward movement of
the baby seat in order to improve safety when riding in different terrains
In order to preserve Nature, Polisport uses non harmful materials
The Polisport family wishes you plenty and pleasant rides
MAINTENANCE
The maintenance of the baby- seat is simple. For good working conditions and to preserve
appearance we advise that you carry out the following:
- Check regularly the fitting system of the baby seat to the bicycle, namely the screws;
- Inspect the safety belts and other components to check they are working effectively;
- Inspect the cleanliness of the baby seat from time to time. When dirty, wash with soap and
water (do not use abrasives, corrosives or toxic products);
- The wadding can be washed with lukewarm soapy water. Hung up to dry.
MOUNTING INSTRUCTIONS
Baby seat was built to be used on bicycles with 26 " to 28" wheels and round tubular frame
with Ø 28 up to Ø 35.
1. Remove the "wallaby evolution" from the packaging and place it as shown in photo.
2. Pull the plates until open.
3. Open the seat back to the furthest position.
4. Keeping the seat back in this position, put the red keys according to the photo, making
them pass through the holes of the seat back and seat bottom. Rotate until you hear a
"click".
Note: the keys must be turned only in the direction shown in the photo
5. Close the plates to fix the position of the seat back.
6. Put the plastic support block and the metal plate fixed around the bicycle tube, at the
highest possible position on the bicycle frame in order to prevent the Wallaby evolution,
when placed on the bicycle, from touching the bicycle's wheel.
7. Start tightening the screws with the longer part of the key in the direction shown in
the picture.
8. Adjust the screws with the shortest part of the screw driver, so that the support block
does not rotate or slide down the bicycle frame.
Note: after the 1 st and 2 nd use, you must verify and rectify the fastening of the screws.
9. Fit the metallic bracket through the holes of the support block, until the safety spring
makes a "click.
10. Adjust the second safety belt to the bicycle frame. The belt must be under tension.
11. To remove the wallaby press the red safety spring and lift the wallaby.
6
FUNCTIONING INSTRUCTIONS
1. The seat can be adjusted in four different positions regarding the bicycle
2. In order to select the wanted back position, open the safety spring and choose from one
of the positions A, B or C.
3. The seat has a marking of the centre of the gravity. After fitting the child seat to a bicycle
this marking should be a maximum of 10cm behind the rear wheel axle, making this ad-
justment through the alteration of the position of the baby seat in one of the 4 positions
available.
4. In order to put the seat in one of the four possible positions regarding the bicycle, pull
the holder that is under the seat.
5. Rotate the holder into the desired position, allowing the forward or back movement of
the seat
6. Once selected the position of the seat, push until you hear a "click"
7. To remove the seat belt, press and pull.
8. The seat belt must be adjusted to the child so it does not disturb or hurt her, in such a way
that the child is secure on the wallaby seat. The adjustment of the length of the seat belt is
done on the rear of the seat back, by sliding the belt through the existing buckles.
9. To regulate the height of the footrests in relation to the seat bottom and bearing in mind
the size of the child, lift the red plates, on the rear of the footrests.
10. Select one of the 9 indicated positions to guarantee the support of the feet so they
do not hang.
11. Once selected the position, lower the plate until you hear a "click"
12. To guarantee the safety of your baby you must keep the belt always adjusted so your
child will not run the risk of hurting herself. You must adjust the belt of the footrests, by re-
moving it from the notch and adjust it to the child's feet without disturbing or hurting her.
SAFETY INSTRUCTIONS
1. The rider must be at least 16 years of age;
2. The baby seat is only suitable for transport of children with a maximum weight of 48.5 lbs
/ 22 kgs, with an age limit of 7 years and check the child's weight regularly. Do not carry a
child that weighs more than this weight.
3. Do not carry a child, who is less than 12 months of age, in this baby seat. To be a pas-
senger, the child must be able to sit up straight with the head held upright while wearing
a bicycle helmet. A doctor should be consulted about any child who is of questionable
developmental age.
4. Do not install this baby seat on a racing style bicycle (drop handlebar).
5. Secure child in baby seat ensuring all safety belts and straps are applied firmly but not so
tight as to cause discomfort to the child; Make sure the seat stays slightly reclined towards
the back and not towards the front, to avoid the child from slipping
The baby seat must never be used before adjusting the safety belt.
6. Do not permit any part of the child's body or clothing, shoelaces, baby seat belts, etc. to
come in contact with moving parts of the bicycle.
7. You are recommended to mount the seat on bicycles coming supplied with wheel-cov-
ers, in order to prevent the child from inserting his feet or hands into the wheel's spokes.
It is also recommended to use a saddle-cover or a saddle with internal springs, in order to
prevent the child from crushing his fingers in the saddle springs.
7