ELICA Space EDS Montaje Y Modo De Empleo página 17

a plug connect the hood to a socket in compliance with current
regulations and positioned in an accessible area. If it not fitted
with a plug (direct mains connection) or if the plug is not
located in an accessible area apply a double pole switch in
accordance with standards which assures the complete
disconnection of the mains under conditions relating to over-
current category III, in accordance with installation
instructions.
Warning! Before re-connecting the hood circuit to the mains
supply and checking the efficient function, always check that
the mains cable is correctly assembled.
Mounting
Note: The hood may be installed both with and without a
chimney.
Before beginning installation:
• Check that the product purchased is of a suitable size for
the chosen installation area.
• To facilitate installation, remove the fat filters and the
other parts allowed and described here, dismantle and
mount it.
To remove see also the relative paragraphs.
• Remove the active carbon (*) filter/s if supplied (see also
relative paragraph). This/these is/are to be mounted only
if you want lo use the hood in the filtering version.
• Check (for transport reasons) that there is no other
supplied material inside the hood (e.g. packets with
screws (*), guarantees (*), etc.), eventually removing
them and keeping them.
• If possible, disconnect and move freestanding or slide-in
range from cabinet opening to provide easier access to
rear wall/ceiling. Otherwise put a thick, protective
covering over countertop, cooktop or range to protect
from damage and debris. Select a flat surface for
assembling the unit. Cover that surface with a protective
covering and place all canopy hood parts and hardware
in it.
• Disconnect the hood during electrical connection, by
turning the home mains switch off.
• In addition check whether near the installation area of the
hood (in the area accessible also with the hood mounted)
an electric socket is available and it is possible to
connect a fumes discharge device to the outside (only
suction version).
• Carry out all the masonry work necessary (e.g.
installation of an electric socket and/or a hole for the
passage of the discharge tube).
Expansion wall plugs are provided to secure the hood to most
types of walls/ceilings. However, a qualified technician must
verify suitability of the materials in accordance with the type of
wall/ceiling. The wall/ceiling must be strong enough to take
the weight of the hood. Do not tile, grout or silicone this
appliance to the wall. Surface mounting only.
Installation without flue
1. Use a pencil to mark the line representing the centre of
the appliance on the wall, as far as the ceiling. This will
make the installation process easier.
2. Position the drilling template on the wall: the vertical
centre line printed on the template should be aligned with
the centre line marked on the wall, and the lower edge of
the template should line up with the lower edge of the
cooker hood.
3. Rest the lower support bracket on the drilling template,
making sure it coincides with the sketched rectangle,
then mark the two outer holes and drill them.
Note: Always make the holes indicated on the template:
the 2 upper holes are used to position the hood, while the
lower holes (generally 1 central or several at the sides)
are used to fix it in place and secure it properly.
Remove the drilling template, insert the rawl plugs and fix
the cooker hood support bracket in place using 2 screws
measuring 5x45 mm.
4. Hang the cooker hood on the lower bracket.
5. Adjust the distance between the cooker hood and the
wall.
6. Adjust the horizontal position of the cooker hood.
7. Fix the cooker
(COMPULSORY!!).
8. Ducting version.
Connect a tube (tube and fixing clamps not supplied;
these are to be purchased separately) for the expulsion
of smoke to the connection ring located above the
suction motor assembly.
The other end of the tube should be connected to a
device for the expulsion of smoke outdoors if the cooker
hood is to be used as a ducted version.
Filter version.
Remove the air outlet connection and apply the anti-
intrusion grille.
Attention! If the hood is not supplied with carbon
filter, then it must be ordered and mounted.
9. Slot the front panel in and perform the necessary
electrical connections for the control panel.
10. Fix the front panel in place using 6 screws (3 per side).
11. Slot in the side panels and fix them in place by sliding
them downwards.
12. Position the upper fixing bracket and secure it using 2
screws.
13. Perform all necessary electrical connections.
Remount the carbon filter frame and the fat/s filter/s and check
the perfect functioning of the hood.
Installation with flue
1. Use a pencil to mark the line representing the centre of
the appliance on the wall, as far as the ceiling. This will
make the installation process easier.
2. Position the drilling template on the wall: the vertical
centre line printed on the template should be aligned with
the centre line marked on the wall, and the lower edge of
the template should line up with the lower edge of the
cooker hood.
3. Rest the lower support bracket on the drilling template,
17
hood to the wall securely