FRIONOR KLV25.4 Manual De Utilización página 3

Dear User
Our aim in presenting you this manual is to ensure that you can use
our aspirators, produced with the state of the art technology within
our modern facilities and supplied to the market subsequent to strict
quality controls, in the most efficient way.
We recommend your esteemed side read carefully this manual and
keep it handy to use it again if required prior to providing information
of usage.
WHAT TO DO BEFORE
INSTALLATION AND USAGE
1. Do not connect the exit of your aspirator to flues where devices
like stoves or water heaters are connected and where there is
circulation of hot gases.
2. The distance between the bottom surface of your aspirator and
the upper surface of electric ovens should be 65 cm stove while the
distance should be 75 cm stove between the bottom surface of your
aspirator and the upper surface of ovens using gas or mixed fuels .
Otherwise, the product will be definitely out of warranty!
3. Insert the plug of your aspirator to the socket when all the usage
switches on the control panel are in closed position.
4. Installation and wiring should be carried out through our
authorized services. Our company is not responsible from failures
arising due to installation by third parties.
5. Be careful that the power cord is not compressed and crushed
during installation. A hole through which the plug of the aspirator can
pass easily must be opened without cutting the aspirator cord and
installation must be carried out in this way. If the power cord is
damaged it must be replaced through our authorized services.
6. If the supply cord is damaged, this cord must be replaced by the
manufacturer or its service agent or equally qualified personnel to
prevent a dangerous situation.
7. Flaming foods should not be cooked under the device. They may
cause fire.
8. The air discharge pipe should be aluminum. The air discharge
pipe should have a length of 120 mm. and louver culvert should be
assembled to the outlet at the exterior without fail. Place the pipe for
flue outlet outside never narrowing the diameter of the pipe (120
mm)
9. Do not use non-fire-resistant filtering materials (such as paper) on
the filter.
10. Turn the unit off and take the plug from the socket prior to the
maintenance process.
11. Use max 6 amp fuse for your safety.
NOTE: Your aspirator is produced to work with and without flue
connection.
USAGE WITH FLUE
There is an air exit on your aspirator. Flue connection will be made
from this air exit. A flue adapter suitable for 120 mm diameter is
supplied with the aspirator. It is recommended to use spiral pipe
with a diameter of 120 mm in the flue pipe. Pipe connection should
be as short as possible and with least number of elbows for efficient
operation of your aspirator.
USAGE WITHOUTFLUE
Closet shelves or cabinet ceilings that may prevent the outlet pipe
should be cut in the same size to ensure air circulation in the
kitchen. The air sucked by the aspirator is given into the kitchen in
usage without flue. A culvert should be installed to the mouth of the
pipe on the facade. Replace your carbon filter every 3 months in
average.
FILTER CHANGE (WASHING)
* Remove the cassette filter by pushing the latches inside.
* Place one side of the filter into the house and secure the filter by
pressing inside and leaving the latch of the other side.
ENGLISH
IMPORTANT NOTICE
1. The distance between the bottom surface of your aspirator
and the upper surface of electric ovens should be 65 cm
stove while the distance should be 75 cm stove between the
bottom surface of your aspirator and the upper surface of
ovens using gas or mixed fuels . Otherwise, the product will
be definitely out of warranty!
2. Place the flue exit in the same diameter (without making it
smaller).
3. Do not operate your aspirator without filter.
4. Do not change the filter while your aspirator is running.
5. Operate your aspirator while you operate your stove.
6. Do not open your aspirator when you feel a gas leak.
7. Wipe your aspirator with cloth soaked in warm water with
detergent and dry.
8. You may use the aluminum filter by washing at least once a
month
9. Replace the oil filter with synthetic fiber every 2 months
10. Replace the imported carbon filter every 3 months in use
without flue.
11. Ventilation of the room should be sufficient if you are
operating your aspirator with products using gas or similar
fuel at the same time.
12. Ensure that the children and people with physical and
mental disabilities do not use the appliance.
MOUNTING AND INSTALLATION
OF THE EXTRACTION HOOD
There are 2 eyelet marks on the back part of your hood for
hanging the hood.
1. Determine the place of the hood which has to be hanged
on a plane surface and at a height of 65 cm from the oven
and mark the hanging hole places.
2. Use a 08 mm drill for drilling and drive the screws by
placing dowels.
3. Hang the hood by using the hanging screws and fix it.
4. There are 2 flues in the parcel of the hood. The short flue is
used for setting the height and the short flue will be placed in
the long flue.
5. Place both flues on the hood at the same time. Make the
flue height adjustment by sliding the short height adjustment
flue from inside upwards.
Drill the 2 eyelet marks on the back part of the hood and hang
the hood on the wall by placing dowels and the screws. Place
the long flue on the hood by sliding it down in the short flue. In
this way assembly of the hood will be completed.