Bosch PS22 Instrucciones De Funcionamiento Y Seguridad página 14

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

2610051963.qxp_PS22 PS32 1/15/19 8:50 AM Page 14
DRILLING WITH VARIABLE SPEED
The trigger controlled variable speed feature
will eliminate the need for center punches in
hard materials. The variable speed trigger
allows you to slowly increase RPM. By using
a slow starting speed, you are able to keep
the bit from "wander ing". You can increase
the speed as the bit "bites" into the work by
squeezing the trigger.
DRIVING WITH VARIABLE SPEED
Variable speed drills will double as a power
screwdriver by using a screwdriver bit in the
drill mode. The technique is to start slowly,
increasing the speed as the screw runs
down. Set the screw snug ly by slowing to a
stop. Prior to driving screws, pilot and
clearance holes should be drilled.
FASTENING WITH SCREWS
This procedure shown in (Fig. 10) will enable
you to fasten ma terials together with your
Cordless Drill/Screwdriver without stripping,
splitting or separating the material.
FASTENING
WITH SCREWS
1. Drill 2/3 diameter and
2/3 of screw length for
soft materials, full
length for hard
materials.
Screw
Apply a slight
even pressure
when driving
screws.
FIG. 10
First, clamp the pieces together and drill the
first hole 2/3 the diam eter of the screw. If the
material is soft, drill only 2/3 the proper
length. If it is hard, drill the entire length.
Second, unclamp the pieces and drill the
second hole the same diameter as the screw
shank in the first or top piece of wood.
Third, if flat head screw is used, countersink
the hole to make the screw flush with the
surface. Then, simply apply even pressure
when driving the screw. The screw shank
clearance hole in the first piece allows the
screw head to pull the pieces tightly together.
The adjustable screw drill accessory will do
all of these oper ations quickly and easily.
Screw drills are available for screw sizes No.
6, 8, 10 and 12.
Always inspect drill bits for excessive wear. Use
only bits that are sharp and in good condition.
TWIST BITS: Available with straight and
reduced shanks for wood and light duty metal
drilling. High speed bits cut faster and last
longer on hard ma terials.
CARBIDE TIPPED BITS: Used for drilling
stone, con crete, plaster, cement and other
unusually hard nonmetals. Use continuous
heavy feed pres sure when employing carbide
tip bits.
Be certain workpiece is clamped or anchored
firm ly. Always apply pressure in a straight line
with the drill bit. Maintain enough pressure to
keep the drill "biting".
When drilling holes in wood, twist bits can be
used. Twist bits may overheat unless pulled out
frequently to clear chips from flutes.
2. Drill same
Use a "back-up" block of wood for work that is
diameter as
screw shank.
likely to splinter, such as thin materials.
You will drill a cleaner hole if you ease up on
3. Countersink
the pressure just before the bit breaks through
same diameter
as screw head.
the wood. Then complete the hole from the
back side.
Adjustable
There are two rules for drilling hard materials.
Screw
Drill
First, the harder the material, the greater the
pres sure you need to apply to the tool. Second,
the harder the material, the slower the speed.
Here are a couple of tips for drilling in metal.
Lubri cate the tip of the bit occasionally with
cutting oil except when drilling soft metals such
as alu minum, cop per or cast iron. If the hole to
be drilled is fairly large, drill a smaller hole first,
then enlarge to the required size, it's often
faster in the long run. Main tain enough
pressure to assure that the bit does not just
spin in the hole. This will dull the bit and greatly
shorten its life.
Variable speed control must be used with
caution for driving nuts and bolts with socket
set attach ments. The technique is to start
slowly, increasing speed as the nut or bolt runs
down. Set the nut or bolt snugly by slowing the
drill to a stop. If this procedure is not followed,
the tool will have a tendency to torque or twist
in your hands when the nut or bolt seats.
-14-
DRILL BITS
DRILLING WOOD
DRILLING METAL
DRIVING NUTS AND BOLTS

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ps32

Tabla de contenido