Using The Appliance; Before First Use - Moulinex HT612 Manual De Instrucciones

DESCRIPTION
a. Mixer
a1. Ejection button to remove
kneaders or beaters
a2. Speed control/ turbo button
b. Multi-blade beaters for light
preparations
(depending on model)
c. Multi-blade beaters for light
preparations
(depending on model)
d. Kneaders for heavy dough
(depending on model)
e. Kneaders for heavy dough
(depending on model)
f. Metal collar
g. Base (depending on model)
h. Bowl (depending on model)
i. Hinged arm lock/unlock button
(depending on model)
j. Mixer lock/unlock button
(depending on model)

BEFORE FIRST USE

• Remove the accessories from their
packaging and clean using warm
water.
k. Spatula (depending on model)
l. Plastic blender shaft (depending
on model)
m. Stainless steel blender shaft
(depending on model)
n. 500 ml mini-chopper
(depending on model)
n1 Bowl
n2 Blade
n3 Reducer
n4 Lid / non-slip base
o. 800 ml blender bowl
(depending on model)
o1 Graduated bowl
o2 Blade
o3 Leak-tight lid
o4 Reducer
o5 Lid / non-slip base
p. Measuring bowl
(depending on model)
Attention: The blender shaft (l or m)
and the blade of the mini-chopper
(n2) and of the blender bowl (o2)
are very sharp. Care should be
taken when handling.
12

USING THE APPLIANCE

Important:
NEVER USE THE BEATERS OR
KNEADERS AT THE SAME TIME AS THE
BLENDER SHAFT, MINI-CHOPPER OR
BLENDER BOWL.
MIXER FUNCTION WITH BEATERS
OR KNEADERS:
• Manual use:
• Check that the appliance is
unplugged, that the speed control
(a2) is set to "0" and that there is
neither blender shaft, nor mini-
chopper nor blender connected to
the back of the appliance.
• Insert the rods of each beater (b)
or kneader (d) into the
corresponding holes and lock into
place. The beaters and kneaders
have a specific shape. The
kneader or beater equipped with
the metal collar (f) should be
positioned to the left into the
biggest hole (Fig. 1).
• Connect the appliance:
- Your appliance has 5 speed
levels and a turbo button. Always
begin mixing or kneading at
speed 1 initially, then move to
speed 2, 3, 4 or 5 (Fig. 2).
- To knead thick dough, we
recommend using speed 5 only.
- You can also increase the speed
by pressing the turbo button. We
however recommend that you use
it only briefly (a maximum of 30
seconds for thick dough).
• After finishing, set the speed control
(a2) to "0".
• Disconnect.
• Then press the ejection button (a1)
to remove the beaters or kneaders.
• Using with the base (g):
(depending on model)
• Check that the appliance is
unplugged, that the speed control
(a2) is set to "0" and that there is
no blender shaft.
• Insert the rods of each beater (c)
or kneader (e) into the
corresponding holes and lock into
place. The beaters and kneaders
have a specific shape. The
kneader or beater with the metal
collar (f) should be positioned to
the left, in the biggest hole (Fig. 1).
• Place the base (g) on the worktop:
- To raise the arm, unlock by
pressing the button (i) (Fig. 3).
- Position the bowl (h) (Fig. 3).
- Press the button (i) to unlock the
arm and lower it (Fig. 4).
- Place the mixer fitted with the
kneaders or beaters on the
hinged arm until you hear it click
into place (Fig. 5).
Note:
INSERT THE MIXER BY POSITIONING
THE BEATERS OR KNEADERS IN THE
NOTCHES (Fig. 5).
• Connect the appliance:
- Your appliance has 5 speed levels
13