Barrette EPN-51808 Guia De Inicio Rapido

To register your product, please visit: barretteoutdoorliving.com
To obtain and review a copy of the warranty please visit barretteoutdoorliving.com.
You may also contact us at 1-877-265-2220 or email Cs.outdoorliving@ebarrette.com
WARNING:
• Improper installation of this product can result in personal injury. Always wear safety goggles when
cutting, drilling and assembling the product.
• Incorrect installation may cause harm to the gate or individual.
• Not pool code approved.
• Do not allow children to play with the gate.
NOTICE:
• DO NOT attempt to assemble the kit if parts are missing or damaged.
• DO NOT return the product to the store, for assistance or replacement parts call: 1-800-336-2383.
Component list:
QTY Description
1 Heavy-Duty Y-Latch
1 Stop Bracket
6 Hex head screws
DOUBLE DRIVE GATE INSTALLATION
1.
Determine Gate Opening:
Determine the gate opening by adding the width of the gates plus clearance of hinges plus a
clearance distance of 1 ⁄ " to 3" for the Heavy-Duty Y-Latch (Fig. 1).
3
4
(See hinge instructions for clearance details.)
NOTE: Mount gate on hinges prior to installing the Heavy-Duty Y-Latch.
2.
Attach Heavy-Duty Y-Latch to Fence Gate:
Place and hold Heavy-Duty Y-Latch on gate upright. Attach Heavy-Duty Y-Latch to gate
upright with three hex head screws (Fig. 2).
3.
Determine Location of Stop Bracket:
While the swing arms are lowered and leveled, place stop bracket flat on the gate while
moving the bracket up or down until the swing arm is level. Once the swing arm is level,
mark with a pencil the stop bracket location on the side of the gate (Fig. 3).
4.
Attach Stop Bracket to Gate:
With the gate opened, place stop bracket on the gate and align with the pencil mark. Attach
stop bracket to gate with the remaining three hex head screws (Fig. 4).
WALK GATE INSTALLATION
1.
Determine Gate Opening:
Determine the gate opening by adding the width of the gate plus clearance of hinges plus a
clearance distance of 1 ⁄ " to 3" for the Heavy-Duty Y-Latch.
3
4
(See hinge instructions for clearance details.)
NOTE: Mount gate on hinges prior to installing the Heavy-Duty Y-latch.
2.
Attach Heavy-Duty Y-Latch to Fence Gate:
a. For walk gates utilizing 2 ⁄ " gate uprights and 2
1
2
can be installed in the same method as the double drive gate installation (Fig. 5).
b. For walk gates utilizing 2 ⁄ " gate uprights and 3" post uprights, the post will serve as the
1
2
Heavy-Duty Y-Latch swing arm stop.
NOTE: Do not install the stop bracket because it will not fit on post upright (Fig. 6).
PADLOCK OPTIONS
1.
Fig. 3, 4 and 5 Heavy-Duty Y-Latch installation should use padlock option 1 shown in Fig. 7.
2.
Fig 6 Heavy-Duty Y-Latch installation should use padlock option 2 shown in Fig. 7.
HEAVY-DUTY Y-LATCH KIT
Installation Instructions
⁄ " post uprights, the Heavy-Duty Y-Latch
1
2
Barrette Outdoor Living
545 Tilton Rd, Egg Harbor City, NJ. 08215
barretteoutdoorliving.com • (877) 265-2220
Read all instructions prior to installing product.
Refer to manufacturers safety instructions when operating any tools.
BEFORE YOU BEGIN:
The primary design of the Y-latch
is for the aluminum double drive
gates with 2 ⁄ " uprights.
1
2
Gate
Upright
2 ⁄ "
1
2
Stop Bracket
Min. Spacing 1.75" Min. Spacing 1.75"
Max Spacing 3.0" Max Spacing 3.0"
Gate Gate
Upright Upright
Gate Gate
Upright Upright
Fig. 5
Post Post
Gate Gate Upright Upright Gate Gate
Upright Upright Upright Upright
EPN-51808
TOOLS NEEDED:
Safety Glasses
Tape Measure
Pencil
Drill
Hex Bit
Swing Arms
Screws
Arm Bracket
Fig. 1 Fig. 2
Gate Gate
Upright Upright
Fig. 3 Fig. 4
Gate Gate
Upright Upright
Pencil Line Pencil Line
Fig. 6 Fig. 7
Padlock Option 1 Padlock Option 1
Post Post
Upright Upright
Padlock Option 2 Padlock Option 2