Publicidad
Idiomas disponibles
Idiomas disponibles
1. MAIN BODY
(with pre-filter bag inside)
2. SUCTION HEAD
G1
3. FLAT NOZZLE & BRUSH
4. BRUSH
5. POLES
6. HOSE SECTION
G2
CONNECTOR X 2
G4
7. HOSE SECTION X 3
8
8. CONNECTORS
HOW TO ASSEMBLE YOUR SKOOBA MAX™
1. Align the rib of the suction head / flat nozzle to the
notch on the nozzle of cleaner hood and then slide
the suction head to the hood until it stops. (Fig.1)
Note: For pools with small filtration flow rate
(eg. 2.0m³/h / 530gal/h), or for cleaning
corners of pools, use flat nozzle instead
of suction head.
2. Select a sufficient number of the pole sections
to suit your pool size. Total length should allow
both hands to grip during operation. Assemble
the pole sections by inserting the grooved end
of one section into the round end of the next
one, finishing with the last section that has the
plastic grip. Slide together until grooved area is
fully inserted. (Fig.2)
3. Insert the grooved end of assembled poles into
the main body securely. (Fig.3)
ASSEMBLE THE HOSE TO THE MAIN BODY
Assemble the hose by connecting all hose sections
with hose connectors provided. (Fig.4)
It is recommended to do this underwater to remove
all entrapped air.
Tips: To remove entrapped air in the hose, place the
hose cuff towards the pool water inlet hole to let
water flow in and push out the entrapped air.
After assembling all hose sections, immerse the
main body under the water. When bubbles stop
coming from the main unit, connect the open end
of the hose to the hose cuff of the body and slide
on as far as it can go. (Fig.5)
CONNECT SKOOBA MAX™ TO THE POOL OUTLET
WARNING!
TURN OFF the pump before connecting
SKOOBA MAX™ to the pool outlet.
1) If you have a surface wall skimmer: Take the open
end of the hose and connect it onto the vacuum plate
of your skimmer. Slide the hose as far as it can go
and apply clamp (not included) to secure it on the
vacuum plate. (Fig.6)
2) If you have a wall skimmer, check your pool manual
or pool dealer for instructions on how to remove the
skimmer weir. Place a skimmer vacuum plate (not
included, check with your pool dealer for the correct model with a cuff connection to fit a
1¼in / 32mm soft hose) over the skimmer filter basket. Connect the open end of the hose
to the vacuum plate cuff, and slide it on as far as it can go. (Fig.7)
IMPORTANT! Make sure the pool water level is over the vacuum plate, otherwise it will suck-in
air during operation.
NOTE: The vacuum plate shown in
(Fig.7) diagrams is for demonstration
only. Please contact your pool dealer
for the correct model. A vacuum plate
with a 90 degree elbow is recommended.
3) If you don't have a wall skimmer:
5 connectors (G1/G2/G3/G4/G5) are provided in the kit to fit the 9 most common types of
strainer (see below) used in above ground pools. According to the strainer used in your pool,
select and attach the correct one to the strainer. Tighten by hand only.
NOTE: For above ground pools with 2 pool water outlets, while connecting the cleaner to one of the
water outlets according to the cleaner instruction manual, follow pool instruction manual to
block the other water outlet. For example, use pool plug to block the outlet or set the control
valve (eg. plunger valve) if available to the closed position. Otherwise, it will weaken the water
flow inside the cleaner and then adversely affect the cleaner performance such as capturing
less debris.
WARNING!
Turn off the pump before closing
the water outlet.
Ø40mm (1
/
in) Strainer plug with
3
5
removable grid cover
Detach the strainer cover and press G3 on it.
Ø40mm (1
in) Strainer plug with non-removable grid cover
3
/
5
Refer to pool instruction manual for how to remove the strainer
plug from the water outlet and then insert G5 connector as shown.
Note: if your pool strainer plug is secured inside the pool water outlet
with pool hose together by hose clamp, you may need to loosen the
hose clamp to release the strainer plug. Pay attention not to let the
pool hose become detached from the water outlet when loosening
the hose clamp. Remove the plug and insert the G5 connector into
water outlet as much as possible. Tighten the hose clamp to
secure the pool hose and the connector to the water outlet.
Ø80mm (3 in) Strainer plug
with removable grid cover
Unscrew the strainer
cover and screw on G1.
POOL VACUUM KIT
3
1
5
G3
G5
x1
2
4
x4
x3
Fig.1
G1
G1
Ø80mm (3 in) Strainer plug with non-removable grid cover
Refer to pool instruction manual for how to remove the strainer
plug from the water outlet and then insert G5 connector as shown.
7
Note: if your pool strainer plug is secured inside the pool water outlet
with pool hose together by hose clamp, you may need to loosen the
hose clamp to release the strainer plug. Pay attention not to let the
pool hose become detached from the water outlet when loosening
the hose clamp. Remove the plug and insert the G5 connector into
6
x3
water outlet as much as possible. Tighten the hose clamp to
secure the pool hose and the connector to the water outlet.
x2
Ø92mm (3
/
in) Strainer
3
5
(with side thread)
Screw G1 onto G4, and
then align and screw
G4 onto the strainer
Ø110mm (4
/
in) Strainer
1
3
Unscrew the strainer cover
and screw G1 onto the
middle thread of the strainer.
Ø36mm (1
in) Strainer Hole
/
2
5
Detach the strainer cover and directly
Fig.2
insert G2 into the strainer hole.
Take the open end of the hose, connect it onto
the connector and slide on as far as it can go.
HOW TO OPERATE YOUR SKOOBA MAX™
When your SKOOBA MAX™ is ready, turn your pump ON
and start using SKOOBA™MAX to clean the bottom of your pool.
Your SKOOBA MAX™ is made to vacuum debris from the bottom of your pool. The internal
Fig.3
pre-filter bag is designed to trap leaves and larger debris, which could otherwise clog the filter of
your pool. Make sure to empty this pre-filter bag regularly to ensure the maximum suction power.
NOTE: Never use your SKOOBA MAX™ without the pre-filter bag. Failure to do so may clog the
filter of your pool.
For vinyl liner and fiberglass pool, it is recommended to keep the brush on the flat nozzle
to avoid damaging to the pool.
IMPORTANT: Trapped air in your vacuum system may
Fig.4
prevent the pump from operating correctly.
In this case, if your pump has a release
valve, open it to let air escape until only
water comes out from it and then close
the valve. Check pump manual how to
remove the air.
HOW TO EMPTY THE PRE-FILTER BAG OF
SKOOBA MAX™
Fig.5
WARNING!
Turn off the pump before
emptying the pre-filter bag.
1. Remove the hood from the cleaner by turning it
anticlockwise until it stops and then take it off
from the main body. (Fig.8)
2. Pull out the pre-filter bag from the cleaner and
remove the leaves and other debris. (Fig.9)
Rinse the cover and make sure its suction hole
is not clogged.
Fig.6
3. Put back the pre-filter bag into the cleaner. Make
sure the notch under the top ring covers the edge
around the opening of the cleaner. (Fig.10) If
pre-filter bag is damaged, replace a new one
before next operation.
4. Align the rid (on the inside surface of hood bottom)
to the slot on the opening of the main body, press
down the hood and turn it clockwise until it stops.
Make sure the hood is secured on the cleaner
before next operation. (Fig.11)
Fig.7
HOW TO REPLACE THE BRUSHES
Lift either end of the brush and then take the brush
completely out from the chamber.
NOTE: Do not pull the bristles forcibly. If it is hard to
take out the brush after lifting the brush end,
use a clamp (not included) to hold the brush
base and then pull the brush completely from
the notch. (Fig.12)
G3
Align the curvature of the new brush to the notch on cleaner head. Insert either end of the brush
to the notch and under the hook and then press the other end into the notch. (Fig.13)
TROUBLE SHOOTING
Problem
Possible Cause
Poor debris
Pre-filter bag is full.
pick-up
Not enough suction
power.
G5
Obstruction somewhere
in the system.
Suction nozzle is blocked.
Suction head
Rolling ball is
does move not
jammed.
smoothly
Hose collapse
Suction is too
strong.
© 2017 Kokido Development Ltd.
All rights reserved. No part of this document may be reproduced or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording,
or otherwise, without prior written permission of Kokido Development Ltd.
G1
Fig.8
Fig.10
2
Solution
Clean the pre-filter bag.
Make sure that your pool pump power is at least 45W, and minimum system
flow rate is 2.0m³/hr (530gal/hr). Make sure the hose is free of punctures.
Check if there are two water outlets on your pool and make sure the water outlet
which is connected with cleaner is opened and the other water outlet is closed.
Clean the pump filter. Clean out any debris from the hose.
Replace a damaged pre-filter bag that lets debris through.
Check and clean out any debris from the nozzle.
Push the rolling ball out from the cavity by inserting a small tool to the small hole
on the top of ball cavity.
Clean it out and push it back into the cavity after cleaning.
Check if your pump power is over 0.5HP/ 375W and /or filtration system flow is
over 1,300gal/5m³.
K563CBX/18
Made in China
17009013
G5
G4
G1
G1
G2
Fig.9
1
Fig.11
Fig.12
Fig.13
Publicidad
