Black+Decker BDCOM400 Manual De Instrucciones página 5

Assembly
Hose and cord storage
Wrap the 12V DC cord around the cord retainer 13 and
u
snap the 12V DC connector (12) into its storage location
on the cord retainer.
The high-pressure hose (8) is located in a storage
u
channel around the face of the unit. Open the lever
on the valve adapter (9) and slide the adapter over the
nub (15) inside the channel. Close the lever to latch the
adapter to the nub.
The accessories are stored on the face of the unit inside
u
the accessory storage area (14) .
The high-volume hose (10) is stored around the edge of
u
the unit and snaps into position at both ends.
Fitting the accessories
Universal valve adapter (Fig. A)
Your inflator is supplied with the standard tapered nozzles
(15) and (16) and the needle inflator nozzle (17) , located on
the front of the unit.
To use the universal valve adaptor (9) , make sure the
u
lever is in the up position.
Place the valve adapter over the stem of the inflator
u
needle or tapered nozzle.
Press the lever (18) on the valve adapter down to lock
u
it in place.
Place the inflation needle or tapered nozzle into the
u
item to be inflated.
Note: Always make sure that the lever is in the up position
when not in use. Operate your inflator only with the
universal valve adaptor or with the included nozzles.
Note: Make sure the universal valve adapter is firmly locked in
place before turning the inflator on.
High-volume hose (Fig. B)
Remove the high-volume hose (10) from the
u
storage location.
Line up the notches (19) of the hose with the nubs (20) of
u
the high-volume pump inflate connection (6) . Then, slide
the hose on and twist counter-clockwise to secure.
To remove, twist the hose clockwise and slide hose off.
u
Note: Many inflatables have an internal flap that prevents air
loss during inflation, especially air mattresses. Unless this flap
is displaced by the nozzle, the inflatable will not inflate. Push
the nozzle firmly into the valve to make sure that you push
this flap out of the way.
Warning! Risk of Bursting. Excessive air pressure may
cause a hazardous risk of bursting or personal injury. Check
the manufacturer's maximum pressure rating for items being
inflated.
(Original instructions)
Note: If the pressure rating for the item being inflated is above
100 psi, note that the maximum run time is 10 minutes, leave
to rest for 20 minutes before reusing.
Switching on (Fig. C)
To turn on high-volume
The high-volume hose is meant to be used for objects that
hold large amounts of air, such as air mattresses, rafts, and
swimming pool floats.
Note: The high-volume mode DOES NOT have an auto
shut-off feature.
Attach the high-volume hose (10) to the high-volume
u
pump inflate connection (6) as described in the "High
volume hose" section.
Insert the hose, or it's tapered nozzle (11) into the object
u
being inflated.
Press the high-volume side of the main power switch (1),
u
indicated by the air mattress symbol (21).
To turn off, push the power switch to the center position.
u
To turn on high-pressure
The high-pressure hose is meant to be used for objects that
need more air pressure, such as tyres and basketballs.
Remove the high-pressure hose (8) from the storage.
u
Attach a nozzle as described in the "Universal valve
u
adapter" section.
Insert the nozzle into the object being inflated.
u
Press the high-pressure side of the main power switch (1)
u
indicated by the tire symbol (22).
To turn off, push the power switch to the center position.
u
Deflate using the high-volume hose (Fig. D)
Warning! Beware of objects being ejected. When deflating,
large amounts of air will exit the high-volume pump inflate con-
nection (6). Ensure the high-volume pump inflate connection
is not pointed at anyone or anything.
Remove the high-volume hose (10) from the storage
u
location.
Line up the notches (19) of the hose with the nubs (23) of
u
the high-volume pump deflate connection (7) . Then, slide
the hose on and twist counter-clockwise to secure.
Insert the hose, or it's tapered nozzle (11) into the object
u
being deflated.
Press the high-volume side of the main power switch (1) ,
u
indicated by the air mattress symbol (21) .
To turn off, push the power switch to the center position.
u
To remove the hose, twist the hose clockwise and slide
u
hose off.
ENGLISH
5