Cequent Performance Products 36507 Instrucciones De Instalación

Fascia
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 36507F
Wrenches: 10mm, 13mm, 19mm, 3/4",
6" Ratchet Extension, Ratchet Swivel
Frame rail
Access
hole
k
j
k
m
j
Qty. (3) Hex Bolt ½-13 x 1-1/2 GR5
k
Qty. (6) Conical Washer 1/2"
l
Qty. (3) Handle Nut Assembly 1/2-13
m
Qty. (3) Hex Bolt M12 x 1.75 x 40mm CL8.8
Recommend: two persons for installation.
1. Lower exhaust by removing (2 (13mm socket )) exhaust hangers per side. This will allow access to frame rail by pushing the
muffler up and outward for clearance.
2. Bend handle nut assembly prior to installation (2) on passenger side and (1) on driver side. Remove until bracket is in place.
3. Raise passenger side bracket into place and install M12 bolt in rearward location. Gently push muffler up and outward for
clearance. Once M12 bolt is started install handle nuts through access holes and attach conical washer and hex bolt. Loosely
install all fasteners.
4. Raise drivers side bracket into position using the same method as in Step 3. Keep all fasteners loose for center-section
installation.
5. Raise center-section of hitch into location and install 7/16" carriage bolts from outside of hitch as shown and attach 7/16 conical
and hex nuts.
6. Check hitch is centered on vehicle.
7. Torque all fasteners to specifications shown below.
8. Re-attach exhaust removed in Step 1.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
2011 Cequent Performance Products - Printed in Mexico
z
Installation Instructions
Dodge Challenger
It is recommended to have (2) people when
Drawbar Kit:
36061
Drawbar must be used in the
RISE position only.
l
Access
slot
l
Existing
weldnuts
o p
Note: sort hardware prior to hitch installation to confirm 1/2" &
n
7/16" conical washer are kept with coordinated 1/2" & 7/16" bolts.
Tighten all M12 CL8.8 fasteners with torque wrench to 68 Lb.-Ft. (92 N*M)
Tighten all 1/2-13 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Dodge Charger
installing this hitch.
Existing
weldnut
k j
o
n
p
Center-section
of hitch
Muffler in place without
rubber isolator shown
n
Qty. (6) Carriage bolt 7/16-14 X 1.50 GR5
o
Qty. (6) Conical Washer 7/16"
p
Qty. (6) Hex nut 7/16-14
Sheet 1 of 3
Part Numbers:
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
3500 LB (1589 Kg) Max Gross Trailer Weight
300 LB (136 Kg) Max Tongue Weight
Wiring Access Location: xxx
Set-up handle nut assembly
prior to installation.
Both side as shown.
k
m
Gently push muffler up and
outward for clearance
36507N 5-23-11
Form F206 Rev A 5605
36507
90130
06128
Rev. A