Publicidad
Idiomas disponibles
Idiomas disponibles
LCD
The contrast and the background colour of the display can
be changed as follows:
-
access the programming mode as described in the sec-
tion "Enter the programming mode";
-
select "LCD" and press
and Contrast.
-
Backlighting
To change the background colour of the screen, you must:
-
select "Backlighting" and press
-
use the buttons
to change the colour and press
confirm.
- Contrast
To change the contrast of the screen, you must:
-
select "Contrast" and press
the current contrast value is
-
use the buttons
to change it and press
Miscellaneous
Inside, you can enable or disable the following functions:
Key X for PWD
-
. Using the button
shorten the procedure required to enable the coded lock
and access the programming mode (Example: press
Password +
).
- YES enables the button
- NO remains disabled.
Extended PWD
-
. Allows the activation of all user pass-
words increasing their number from 20 to 250.
- YES enables 250 passwords.
- NO enables 20 passwords.
Disable tone.
-
Enable/disable keypad tones.
- Yes disables all keypad tones.
- NO enables all the tones.
To access the programming mode, you must:
-
access the programming mode as described in the sec-
tion "Enter the programming mode";
-
select "Misc." and press
PWD, Extended PWD and Disable tone;
-
select one of them by pressing
-
choose YES or NO with
-
continue with other programming or return to the list of
programming by pressing
Default.
To restore the keypad setting made at the factory and then
delete all changes made during programming you must:
-
select "Default" and press
Yes;
-
press No not to delete the programming made, press Yes
to restore the default settings and delete the recently ones
made.
Version.
Inform about the software version of the keyboard.
, the display shows
Backlighting
;
, a horizontal bar indicating
shown;
.
(instead of 00+
for this function.
;
the display shows:
Key
and press
;
and press
to confirm;
.
;
the display shows
No and
Restoring the Administrator Password.
If you lose the administrator password you can reset the
factory one assigned by default (0039) as follows:
-
cut the power supply to the keyboard;
- simultaneously press the buttons 1, 3 and 0;
- restore voltage to the keyboard and hold pressed the
buttons 1, 3 and 0 until the message "Default Admin.
Password" is displayed;
- release the buttons; now the password 0039 is restored.
to
OPERATION
Check that all connections are correct. Connect the power
supply unit to the mains; the push-button panel automatically
checks the status of the line displaying for 5 seconds
"TD6100PL / Release....."; at the end of checking, in case of
failure, the display shows "ERROR....." in case of a positive
check on the display appears the message "Press
select the number" alternating with "Press
Dial the number or select the desired user name (if previ-
ously stored) by pressing the
desired user name appears on the display press the
) to
make a call.
In case of error press
+
dial the correct to number.
If the line is free, you will hear a confirmation tone and the
display shows "Call in progress---"; the extension rings for
the number of times defined by programming "Ringtone -
Number of rings".
If press
the call is terminated and the system is ready for
a new call.
The called user picks up the handset enables the
conversation with the external station for 60 seconds. The
display shows "Connection ---- ".
The display of the door station starts flashing 10 seconds
before conversation ends. To continue conversation for
additional 60 seconds press
From the internal station, press the
the door lock; this operation requires that the user is in
for
conversation and wait about 1 second after lifting the hand-
set. The lock release activation time is defined by program-
ming "S1-S2" (page 13).
Replace the handset or press
restore the idle state.
Numbers that are not sent or deleted go off after 25 seconds.
In installations with 2 or more main push-button panels,
when a call is made from one push-button panel, the other
push-button panels are deactivated with the busy signal.
Wait until the line is free to make the call.
Door lock opening
The door lock can be opened from the push-button panel,
including in "busy" mode, by dialling one of the 4-digit
passwords you have entered.
to call the user".
or
buttons, once the
(only before sending the call) and
again (up to 3 times).
button to release
on the door station to
Mi 2472
to
to
14
Publicidad
