Technical Data; Vibration Information - Drel CON-EAS-1301 Manual Del Usuario

instructions below:
PL
Pull the cover forward completely.
Push the Bit Tray fully (7) out of the tool.
EN
Remove the Bit Tray (7) from the shaft (a). Replace the
bits with appropriate ones. Make sure that the bits are
BG
properly aligned in the tray and do not protrude from
the back.
CZ
Insert the Bit Tray (7) back onto the shaft and push it
completely into the tool.
Press the Cover back and make sure that it is completely
DE
closed.
ATTENTION:
ES
Only 25 mm bits are compatible with the screwdriver.
If the Cover is not completely removed, the Bit Tray will
FR
be locked when it is pulled out of the tool. Pull the cover
forward completely.
HU
The cover may not close completely if the Bit Tray is not
properly positioned inside the device. Make sure that the
IT
Bit Tray is in the appropriate position when selecting a
correct bit. If the cover does not close properly, try tur-
RO
ning the mounting a little to the right or to the left and
try again.
SWITCH LOCK
RU
The screwdriver's switch can be locked in the "off " po-
sition. It limits possible accidental switching on when
SK
the screwdriver is not in use.
To lock the switch, set the rotation control switch (2) to
the middle position.
ROTATION DIRECTION CONTROL SWITCH (SEE
FIG. F1, F2)
To drill and screw in a clockwise direction
set the switch to position "<<", for rotation in the oppo-
site direction, set the switch to the ">>" position.
Do not change the rotation direction while the
WARNING:
device is running, wait until it stops completely!
FULLY AUTOMATIC LOCKING SYSTEM FOR THE RO-
TATING ELEMENT (AUTO-LOCK) (SEE FIG. G)
Bit mounting (6) locks when the device Switch (4) is not
pressed. Thanks to it, the screwdriver may be used in the
manual mode when necessary.
Important: When the device is used in the manual
mode, do not press the switch (4). It may damage the
screwdriver.
USING THE LED
10
To turn on the LED, press the switch (4). When the switch
is released, the LED will turn off .
The LED increases visibility and works well in dark, cram-
ped rooms.
BATTERY CHARGE LEVEL INDICATOR (SEE FIG. H)
Press the button (4) to check the battery charge level.
When the red battery charge indicator turns on, this me-
ans less than 30% of the charge and the battery must
be recharged.

TECHNICAL DATA

Model:
Battery voltage:
Battery capacity:
Battery type and number:
Unloaded speed:
Max. torque:
Device weight:
Charging time:
Charger protection class:
Charger voltage:
Output voltage:
Charging output current:
ACCESSORIES
25 mm bits (PZ1 PH1 PH2 S4 S6 T10) - 6
Charger 3-5 h - 1
Bit tray - 1
Use good quality accessories of a reputable brand. We re-
commend using DREL or JUFISTO accessories. A tool type
should be selected according to the planned works. More
information can be found on the packaging. Store staff
can help and advise you.
NOISE LEVEL INFORMATION
A-weighted sound pressure level LpA = 64.76 dB (A) KpA
= 3 dB (A)
A-weighted sound power level LvA = 75.76 dB (A)
KwA: 3 dB (A)
USE HEARING PROTECTION.

VIBRATION INFORMATION

Total vibration value (triaxial vector sum) determined
according to EN 62841: Vibration emission value: ah =
0.216 m/s2 Uncertainty K = 1.5 m/s²
CSD36H
3.6 V
Lithium-ion 1.5 Ah
INR 18/65
230 rpm
4.5 Nm
0.48 kg
3-5 hours
/II
100-240 V~ 50/60 Hz
5 V
600 mA