Low Battery Warning - DeWalt DCD200 Traducido De Las Instrucciones Originales

• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
Variable Speed Trigger Switch (Fig. A)
To turn the tool on, squeeze the trigger switch
tool off, release the trigger switch. The tool speed is controlled
by varying the trigger position.
nOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should
be avoided.
Forward/Reverse Control Button (Fig. A)
A forward/reverse control button
direction of the cable and also serves as a lock-off button.
To select forward rotation, release the trigger switch and
depress the forward/reverse control button on the right side of
the tool.
To select reverse, release the trigger switch and depress the
forward/reverse control button on the left side of the tool.
The centre position of the control button locks the tool in the off
position. When changing the position of the control button, be
sure the trigger is released.
nOTE: The first time the tool is run after changing the direction
of rotation, you may hear a click on start up. This is normal and
does not indicate a problem.
nOTE: The tool must come to a complete stop before changing
the tool's direction or running the tool in the opposite direction.
Front Handle/Cable Lock (Fig. A)
The front handle 10 has a lock position and unlock position.
When pushed forward, the front handle will unlock allowing the
cable to be pulled out of or pushed into the drum. When pulled
backward, the front handle locks the cable into position.
Adjustable LED Worklight (Fig. A, C)
The adjustable LED worklight 7
of the fixed drum shield 8 . The worklight switch
located on the foot of the tool's main handle
is activated when the trigger switch is depressed. The low,
medium and spotlight modes can be changed by moving the
switch . If the trigger switch remains depressed, the worklight
4
will remain on in all modes.
When on low and medium settings, the beam will stay
illuminated for up to 20 seconds after the trigger switch
is released.
Spotlight Mode
The high setting is the spotlight mode. The spotlight will run
for 20 minutes after the trigger switch is released. Two minutes
before the spotlight will shut off, it will flash twice and then dim.
To avoid the spotlight shutting off, lightly tap the trigger switch.

WARNING: While using the worklight in medium or
spotlight mode, do not stare at the light or place the
tool in a position which may cause anyone to stare
into the light. Serious eye injury could result.
2 . To turn the
determines the spin
1
(Fig. A) is located on the base
4 , Fig. C, is
. The worklight
3

CAUTION: When using the tool as a spotlight, be sure
it is secured on a stable surface where it will not cause a
tripping or falling hazard.

CAUTION: Fully retract the cable into the drum before
using the tool as a spotlight. Personal injury or property
damage could result.

Low Battery Warning

When in spotlight mode and the battery is nearing complete
discharge, the spotlight will flash twice and then dim. After two
minutes, the battery will be completely discharged and the
tool will immediately shut down. At this point, replace with a
fresh battery.

WARNING: To reduce the risk of injury, always have a
back-up battery or secondary lighting available if the
situation warrants it.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
e
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool
Handle
1. Align the battery pack with the rails inside the tool's
5
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button
6
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button 6 . A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
EngLIsh
WALT battery packs and chargers.
is fully charged.
5
and firmly pull the battery pack
33