Publicidad
Enlaces rápidos
ROTATING IRONING BOARD
NOTE:
Depending on application and panel
construction, you can install the Elite
Rotating Ironing Board as follows.
1) Use either machine or wood screws to
mount the unit directly to the top of the
shelf. This installation provides a 3/16"
(4.76 mm) clearance and intended for
applications without a drawer front.
2) Use machine screws and included
spacers to mount the unit to the top of
shelf. This installation provides a 7/8"
(22.23 mm) clearance and intended for
applications using a drawer front.
Note: Minimum shelf dimensions
required: 14" (356 mm) deep and 22"
(559 mm) wide
TOOLS REQUIRED:
ESTIMATED ASSEMBLY TIME:
20 MIN
CARE AND MAINTENANCE:
Ironing Board: Clean with a damp
cloth and wipe parts dry.
Cover: Spot clean as necessary.
WATCH TUTORIALS OF OUR
PRODUCTS BEING INSTALLED
WWW.REV-A-SHELF.COM/VIDEOS
No.
A
B
#2
#2
#2
C
D
E
F
A
D
INSTALLATION INSTRUCTIONS: ROTATING IRONING BOARD
PARTS LIST
Description
Rotating Ironing Board w/ Soft-Close Slides
#8 X 5/8" Wood Screws
1/4" Washers
1/4" -20 x 1" Round Head Screws
5/8" Metal Spacer
1/4" - 20 x 1-3/4" Truss Head Screws
B
E
F
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
Qty.
1
8
4
4
4
4
C
I-CROIBSL-0321
Publicidad
Resumen de contenidos para Rev-A-Shelf CROIBSL-COVER-52
- Página 1 12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 ROTATING IRONING BOARD NOTE: Depending on application and panel construction, you can install the Elite Rotating Ironing Board as follows. 1) Use either machine or wood screws to mount the unit directly to the top of the shelf.
- Página 2 STEP 2 Line up the ironing board frame with the pre-drilled holes and using (8) #8 x 5/8” wood screws secure it to the shelf. FIG. 1B Install the wood screws top down (See Figure 1B) Customer Service: 800-626-1126 | rev-a-shelf.com...
- Página 3 METHOD 2 (MACHINE SCREWS FOR 3/16” CLEARANCE SHELF FIG. 2A Min. 22” (560 mm) 7-9/16” (192 mm) STEP 1 Measure and pre-drill (4) pilot holes using a 5/16” drill bit. 5/16” (8 mm) (See Figure 2A). CENTER LINE (FRONT EDGE) STEP 2 FIG.
- Página 4 (See Figure 3B). ALL METHODS FIG. 4 STEP 3 Using the front finger slot, pull the ironing board out, extend the support rack and unfold the board (See Figure 4). Support Rack Customer Service: 800-626-1126 | rev-a-shelf.com...
- Página 5 12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 INSTRUCCIONES DE INSTALACIÓN / LES INSTRUCTIONS D’INSTALLATION TABLA DE PLANCHAR GIRATORIA / PLANCHE À REPASSER PIVOTANTE NOTA: / REMARQUE: Dependiendo de la aplicación y la construcción del panel, puede instalar la tabla de planchar giratoria Elite de la siguiente manera.
- Página 6 Alignez le cadre de la planche à repasser avec les trous prépercés et utilisez 8 vis à bois de 15,87 mm (5/8 po) pour le fixer à l’étagère. Installez les vis à bois de haut en bas (voir la figure 1B). Customer Service: 800-626-1126 | rev-a-shelf.com...
- Página 7 MÉTODO 2 (TORNILLOS DE MAQUINA PARA UN ESPACIO DE 3/16”) ESTANTE / ÉTAGÈRE FIG. 2A Min. 22” (560 mm) MÉTHODE 2 (VIS MÉCANIQUES POUR UN 7-9/16” (192 mm) DÉGAGEMENT DE 4,76 MM (3/16 PO) 5/16” (8 mm) PASO 1 / ÉTAPE 1 Mida y taladre previamente (4) orificios guía con una broca de 5/16”...
- Página 8 À l’aide de la fente avant pour les Rack de soporte doigts, tirez la planche à repasser, Support de support allongez le support et dépliez le planche. Customer Service: 800-626-1126 | rev-a-shelf.com...